Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Nearly 100 Exotic Wood Species, Direct-Imported Since 1972. Shop Slabs & Turning Stock.

Renaissance wax

Posts

Renaissance wax

#1

Renaissance wax

Bill Hale / The Wood Spinner

>Had heard lots about it so I finaly decided to buy some. Boy was I suprised by the price, $ 15.00 for a tiny can.

Ok, I have it now, how do I use it? I am sure at that price I don't just put it on a rag and wipe it on like Minwax.

Bill in CG, AZ.

Re: Renaissance wax

#2

Re: Renaissance wax

Danny Wells

>A little dab'l do ya. Apply a thin layer while the lathe is spinning or not. Let it dry to haze...then buff it. Works great as a final finish for anything that will be handled. Does not show finger prints.

Re: Renaissance wax

#3

Re: Renaissance wax

Vince

>Hi Bill,

I used this product on small projects. I usually use it over lacquer finish. It will not get real shiny but it hardens and helps eliminate finger and smudge marks. It is a good product for the right projects.

Vince

Re: Renaissance wax

#4

Re: Renaissance wax

Carole Valentine

>Just a tiny bit is all you need. Buff it vigorously. I use it on almost all of my turnings, especially ones that will be handled at a show. I have the 500ml can and I suspect it will last me a lifetime if I don't lose it.

Re: Renaissance wax

#5

Re: Renaissance wax

Cyril Griesbach

>I've heard it's also inert so it should not go bad over time.

Re: Renaissance wax

#6

JL

Re: Renaissance wax

JL

>I also use just a little bit (maybe the size of a small marble) to wax the top of my table saw. I use smaller amounts for the band saw table and jointer table.

Re: Renaissance wax

#7

Re: Renaissance wax

Bill Hale / The Wood Spinner

>Nobody has answered, how do I apply it !

Bill

Re: Renaissance wax

#8

JL

Re: Renaissance wax

JL

>I put a little bit on a shop towel and wipe it on, then buff off.

Re: Renaissance wax

#9

Conservator's Wax-Lee Valley *LINK*

Jennifer@Indy.USA

>Bill,

I use Lee Valley's version of this stuff. It's called Conservator's Wax and is about $9.50 for the same stuff.

Jennifer


Lee Valley's Version

Re: Renaissance wax

#10

Re: Renaissance wax

georgetroy

>I use 4000 steel wool to apply and make it go as far as possible. The only thing is I HATE THE SMELL

Re: Renaissance wax

#11

Re: Renaissance wax

Barbara Gill, Remlik VA

>I keep a little piece of cloth in the can. After I have gone through the Beall steps I rub a little on the piece and buff with a dedicated buff.

Re: Renaissance wax

#12

Re: Conservator's Wax-Lee Valley

Carole Valentine

>I will have to disagree with you about them being the same, Jen. I bought the Lee Valley brand after I lost my first can of RW. I used it on a couple of pieces and went and got a replacement can of RW. It did not seem to dry nearly as hard as RW and was a much different consistency (much softer - maybe more solvents)

Re: Renaissance wax

#13

cloth in can

JohnKJordan in East TN

>>I keep a little piece of cloth in the can.

I do the same - the piece of cloth never dries out and is always ready to use. Just open the can, squish a tiny bit more on the cloth if necessary, and apply all over the piece. Rather than a buffing wheel, I buff by hand with a piece of soft cotten cloth (old t-shirt material).

I also use the stuff on my lathe tool rest. I've had one can four years now and it's still 11/15ths full.

JKJ

Re: Renaissance wax

#14

Re: Renaissance wax

Juergen

>Barbara has it right idea. Keep a small piece of cloth (Old T-Shirt) in the can and wipe on lightly. The instruction on my can indicate one does not have to wait for the wax to dry (haze-up). I have found over many years of use that buffing with a clean T-Shirt or cotton cloth works well. I've mounted a some sheep skin (with wool) on the side of my buffing wheel, it does an amazing job of bringing out the luster.

Re: Renaissance wax

#15

Re: Renaissance wax

Colin Spencer

>Bill

AS everyone else has said just a small amount on the turning. I use it on all my turnings. If I buff the item with the Beall process I do not use Carnuba for the final buff but use RW applied to the piece and then buffed on the wheel. It allows pieces to be handled without fear of the surface becoming marred in any way.

Re: Renaissance wax

#16

Re: Renaissance wax

Bill Hale / The Wood Spinner

>Thank you all so much !

Good turning, be safe and have a happy holiday

Bill in CG, AZ.

Re: Renaissance wax

#17

Re: Renaissance wax

Tim GC

>A small further question ... do you just use bare hands to hold the piece while buffing the Renaissance wax??

Re: Renaissance wax

#18

Re: Renaissance wax

Stuart Johnson

>I do. I also think two or three light coats does a better job.

Re: Renaissance wax

#19

Re: Renaissance wax

Wally

>I'd like to use it on turned wine stoppers. Will the RW hold up to damp hands with either wine or H2O on them? If not then what would be best to use? Thank You!

Re: Renaissance wax

#20

Re: Renaissance wax

Carole Valentine

>You know Wally, that's a good question. I have not used it on utility items. On Wine stoppers I just use a penetrating oil finish and/or a little Butcher's Wax. I figure that is easy for the user to renew if necessary.