Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Need a tree taken down or milled?

faceplate safety question

Posts

faceplate safety question

#1

faceplate safety question

Steven Kubien

>Ok, since my incident with the stuck faceplate I have finally decided to get out my Beall spindle tap and make some wooden faceplates. Question is how large/heavy a blank can I put on one? I have some 1-1/2" beech I am planning to use and actually cut a 4" round this evening. Can I put a 50lbs maple bowl blank on it, using decent screws or lag bolts with confidence or am I asking for trouble? Would it be better if I made a larger diameter faceplate?

I drilled and tapped the hole and then thought I had better ask before I do this.

Thanks,

Steve Kubien

Re: faceplate safety question

#2

Re: faceplate safety question

jwoodwright

>I'm all about Safety and that voice screaming at me says NO!!!

You heard it as well, that is the voice of Common Sense who then becomes Hindsight, when we don't listen.

There is a reason they sell 8 Inch Steel Face Plates.

The smaller Shop Made Face Plates are great where you would use a smaller glue block.

Compare the 4 in Wooden Face Plate to the Large piece of Maple, not much to grab.

You've heard of folks using a Chuck to hold one that Large, they "get away" with it for a while, then you here about the New Shop Window that wasn't planned...

Take care and be Safe.

John

Re: faceplate safety question

#3

Re: faceplate safety question

Rick Allen

>If you use the tailstock for support the wood faceplate will work great.

When you get the 50 LB blank down to 10 lbs or less and the tailstock is in the way then would trust the wood faceplate.

Watch the grain for where you put the holes for the screws.

Better would be to buy a few steel faceplates that fit.

Re: faceplate safety question

#4

Large blanks need metal faceplates.

Brian Hahn in SW Wisconsin

>I'd never trust a tapped wooden faceplace for anything that large.

A new steel or cast iron faceplate is a lot cheaper than a trip to the emergency room.

Just my $0.02

Re: faceplate safety question

#5

Re: Large blanks need metal faceplates.

john lucas

>I agree with Brian. A new faceplate is about the same price as the Beal tap. Simply put a piece of milk bottle plastic between the faceplate and spindle and you won't have the stuck problem again. I would not trust wood for anything other than maybe a lightweight platter.

Re: faceplate safety question

#6

Re: faceplate safety question

Cyril Griesbach

>Steve, why not consider the faceplate rings that are available that are held in a chuck?

Re: faceplate safety question

#7

Re: faceplate safety question

Barry Irby

>I would be reluctant to use wooden faceplates for anything much heavier than the faceplate. My fear would be that the wood would split and the whole thing would come off the lathe.

If I were going to do this I think I would try laminating about three pieces of Baltic birch type plywood together to get lots of different grain orientations and avoid any possible fracture lines.

Mind you, I have not had one fail and have never used one, its just that little voice thing that has kept me alive so far. (I needed to get a better or more attentive little voice, I have been wounded a few times.)

I'm with John on this, clean and wax or lub the shaft and use a milk jug washer.

Re: faceplate safety question

#8

Re: faceplate safety question

Bill Hale / The Wood Spinner

>Why not just start between centers and shape the outside of the piece with a spigout. Rotate it into a jaw chuck, pull up the tailstock to rough out most of the inside , then remove the tailstock and finish.

I do this as my normal system. I put pieces on the lathe a lot heaverier than 50 lbs.

Good turning and be safe

Bill in CG, AZ.

Re: faceplate safety question

#9

Re: faceplate safety question

Allen Neighbors

>Steven, I've used many Oak face plates that were tapped for my 1x8" spindle on the old lathe. They are very good for lighter stuff. I wouldn't suggest putting a wooden faceplate on a 50 pound chunk of wood. I have a four inch faceplate that came with my Oneway, and I've used it on a ninety pound chunk of Oak. 8 screws. Only way to go on large blanks.

Don't save $50 bucks and then spend $5000 in ER, friend.

Allen

Re: faceplate safety question

#10

Thanks everyone

Steven Kubien

>I appreciate all of the responses. The tide seems to be shifting towards caution and yeah, I do hear that little voice inside my head from time to time. Not sure why I didn't think of getting one of the Nova faceplate rings since I use Nova chucks. Duh!

Thanks again.

Steve Kubien

Re: faceplate safety question

#11

Re: Thanks everyone

Dale Bright

>Have you thought about drilling and tapping the bowl blank directly and turning it with the tailstock until you turn a tenon for your chuck? I have the Beall spindle tap but I have yet to use it.

Re: faceplate safety question

#12

Re: Thanks everyone

Carole Valentine

>Steve, I use the Nova faceplate rings and love them. I made a donut-like center out of MDF that accomodates my centering thing for centering the faceplates.

Re: faceplate safety question

#13

Could you explain that?

Steven Kubien

>Carole,

Could you expand on the centring thing? My brain is a little fuzzy right now and I'm not 'getting' it.

Thanks,

Steve

Re: faceplate safety question

#14

Mike Stafford

It must be a woman thing.....

Mike Stafford

>

Re: faceplate safety question

#15

Re: faceplate safety question

Peter Hyde

>Steve,

I use wood face plates very often, but I make then from 2 layers of 5/8 baltic birch ply. I also use a glue and paper joint with them and have never had a problem. If you have a long good fitting thread into the ply I can't see what would be a safety problem especially if you are also using the tail stock and turning between centers. I have seen well known turners cut spigots on a blank held between centers with just compression against chuck jaws. Here's the last batch of 6" and 8" I made a few weeks ago.


img

Re: faceplate safety question

#16

Re: Nope, it's a 'smart' thing.

Allen Neighbors

>It's a circular piece with a cutout the size of the faceplate ring in the center. Center the donut on the blank, and put the faceplate ring in the cutout... bam... it's centered. Beats fooling around with a ruler, etc. :)

Re: faceplate safety question

#17

Hey Peter...

Steven Kubien

>...are the two pieces just glued together or is there mechanical fasteners (screws) that I just can't see? What sort of glue has worked best for you? Regular yellow wood glue or polyurethane?

Thanks,

Steve Kubien

Re: faceplate safety question

#18

Well duh!

Steven Kubien

>Thanks Allen. That makes sense. Forgive my slow brain. It's the only one I've got right now!

Steve Kubien

Re: faceplate safety question

#19

Re: Hey Peter...

Peter Hyde

>Steve,

The 2 pieces are glued only. I use Wurth pva but any good wood glue will work. I use the lathe to drill the blanks and then with the lathe off use the tailstock to support and center the tap as I turn the faceplate by hand. The smaller piece on the back is cut with a circle jig prior to gluing and this is then held in a chuck for the drilling and tapping process. Once the hole is threaded then I reverse it screw it on to the spindle and true the back face. Then mount it the right way around and true the front and rim and use a 3 point tool to cut the guide rings.

The spindle on my lathe has a thread long enough to engage the 2 layers of ply. I would not put a 50lb block on a 4" wood face plate or a steel one either. But I have used bigger sizes for heavier blocks with no problems even without tailstock support.

These wood faceplates really make off center work a lot easier to mount as you can put your fixing screws in anywhere.

HTH

Re: faceplate safety question

#20

Not exactly.

Carole Valentine

>I will take a pic this afternoon.

Re: faceplate safety question

#21

Re: Picture coming... I may not...

Allen Neighbors

>be as smart as I thought. :)