Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Build it. Rock it. Rockler has your woodworking tools.

Drilling glass OT?

Posts

Drilling glass OT?

#1

Drilling glass OT?

Bill Crommett

>Can anyone tell me how to drill a tiny (1/ 16 in.) hole in the bottom of a wine glass. I have drilled larger holes in heavier glass, and have broken more than my share of bottles while drilling holes. I have never attempted to drill a hole this small, though.

Re: Drilling glass OT?

#2

Re: Drilling glass OT?

jwoodwright

>I've done bottles in the past with the friction method.

Basically, you make a Plumbers Putty Dam, use Carborumdum Dust and a wood dowel. Make a paste and allow friction to make the hole.

1/16" is damn small, maybe a laser?

If you went to 1/8", could use a Bamboo Skewer, cut about 2" long, chucked into a VS Drill...

John

Re: Drilling glass OT?

#3

jim miles

Re: Drilling glass OT?

jim miles

>I have had success drilling holes in wine bottles with a bit made to drill ceramic tile. You have to keep water pouring over it to keep from breaking. Good luck

Re: Drilling glass OT?

#4

Re: Drilling glass OT?

john lucas

>1/16 is might small. I have some diamond abrasive bits that fit my Dremel that will do that. I've drilled glass using other abrasive wheels in the Dremel. To drill larger more accurate holes I use the Diamond drill and clay dam method.

Re: Drilling glass OT?

#5

Re: Drilling glass - yes *LINK*

JohnKJordan in East TN

>Bill,

You can drill a hole in glass with grit, as mentioned. It's been a long time since I tried it, so I drilled a 1/16" hole in the side of an old mason jar. (I better throw it away now before my wife cans some more pickled okra!) Instead of a wood dowel, I used a short piece of brass rod chucked in a drill press. Even better would be a piece of brass tubing. Aluminum should work as well.

My drill press at the slowest possible speed was still faster than I would prefer but it worked. For grit I used automotive valve grinding/lapping compound with a drop of oil added to thin. I applied fairly light pressure, enough to hear the grinding. Repeatedly lifting and lowering the "bit" helped to bring more grit to the tip of the rod. I stopped and flattened the rod a couple of times since it was rounded off quickly. A tube should work better.

Note that you will get chipping on the inside as you break through unless the glass is backed up firmly.

Although this method will work, it's pretty slow. A blunt end diamond drill bit is far easier.

JKJ


diamond drill bits

Re: Drilling glass OT?

#6

Peter Charles Fagg (UK)

Re: Drilling glass OT? A small tip

Peter Charles Fagg (UK)

>I have recently retiled my bathroom and had to drill several holes. In order to stop the masonry drill wandering use some sticky tape (Sellotape or Insulating) at the point where you want to penetrate,I feel sure that it will work with glass the hardness of the surfaces is about the same.

The ONLY time I have drilled glass was for an outside light that filled with water in gale conditions, I used valve grinding paste and a Stainless steel rod. Slow but very neat hole.

Regards, Peter.

Re: Drilling glass OT?

#7

Re: Drilling glass OT?

Doug Turner

>Go see your dentist. He will probably give you a used diamond drill bit that is 1/16" or slightly smaller. The shaft is only 1/16" but that works in a drill press chuck. As mentioned above liquid cooling and VERY light pressure will do the job.

Re: Drilling glass OT?

#8

Re: Drilling glass OT?

Barry Irby

>I was going to suggest taking the glass to the dentist and have him drill the hole. Shouldn't be much harder than drilling a tooth and there is no face to get in the way. You can spit on it once in a while to make him feel more comfortable and to keep the bit cool.

BTW, Why are we helping you make a leaky wine glass? Upon whom are we playing a trick?

Re: Drilling glass OT?

#9

Re: Drilling glass OT?

Bill Crommett

>Thanks to John, Jim, John, JKJ, Peter and Doug. I have the answer to my problem, but nobody wanted to know why such a small hole in a wine glass. One of my Christmas project is to make a "dribble" glass which was a great seller for Johnson and Smith back in the thirtys along with the Whoopy Cushion and the Joy Buzzer. OK, too ancient for most of you but a fond memory for the other five of us.

Re: Drilling glass OT?

#10

Re: Drilling glass OT?

Bill Crommett

>Barry wins the prize for being nosy. My kind of guy !

Re: Drilling glass OT?

#11

All Right! I thought it sounded like a Dribble

Barry Irby

>Glass. My aunt had some when I was a kid. She had a set of about eight, only one or two of which dribbled. It was hysterical to watch people struggle to keep it from dribbling while those around them calmly sipped their drinks for the non-dribble glasses.

Hers had little decorative slots cut abut a half inch down from the rim. Little slashed that looked like grains of wheat. Only on some glasses the just barely went through. You filled the glass to the ordinary height but when the unsuspecting victim tipped the up to drink, dribble, dribble. I bet you could cut the slots with a grinding wheel on a Dremel.

Re: Drilling glass OT?

#12

Re: All Right! I thought it sounded like a Dribble

Bill Crommett

>Good Thought, Barry. I will contemplate that one.

Bill

Re: Drilling glass OT?

#13

Re: Drilling glass OT?

Bob Macgregor

>A while back I was researching self-starting siphons for a livestock water-tank and ran across old designs for gag tea cups that would drain themselves after being filled above a certain level. This sounds like a similar trick. A great laugh as long as you aren't the one left holding the gag!