Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

VPS-Level Performance. Fully Managed. No Hassle.

Lathe Hight

Posts

Lathe Hight

#1

Lathe Hight

Lester Gillett/Independence Mo

>After turning some pens to day my back is sore from bending over. How

have you raised your lathe up to a good hight? Would like to see some

photos of how you did it. Was thinking of making 4 small blocks and

setting each leg on them. Not sure if it will make the lathe stable.

Lester

Re: Lathe Hight

#2

Re: Lathe Hight

JohnKJordan in East TN

>Rather than four small blocks, you might make two longer blocks and use one for both feet on one end.

JKJ

Re: Lathe Hight

#3

Re: Lathe Hight

Allen Neighbors

>Lester, this is how I did my risers. I'll just post this one pic. After bolstering up under the floor joists, I screwed down a 2x6 to fit each end of the lathe footprint, then screwed down another on top, giving me a total lift of 3". I lag-bolted the lathe down to the 2Xs to make sure it didn't walk off the risers. My spindle height is now 49" from the floor, and I don't have to stoop so much.

I used to have back and shoulder trouble... now I don't... I love it.


img

Re: Lathe Hight

#4

Re: One more try for the pic. 

Allen Neighbors

>


img

Re: Lathe Hight

#5

Dick Hines

Re: Lathe Hight

Dick Hines

>I have my PM sitting on 4x4's. Saves my back.

Re: Lathe Hight

#6

Re: Lathe Height

Carol - now in NC Nebraska

>Lester, the spindle at maybe 1 inch above the inside of your elbow from the floor has been mentioned in earlier posts.

At least it is a place to begin. :)

Re: Lathe Hight

#7

Re: Lathe Hight

Bill Hale

>Remember what you are going to put on the floor where you turn. I stand on 1" thick heavy rubber mats. I have these all around the lathe and so when I drop a tool it never hurts the edge.

Good turning and be safe,

Bill in CG, AZ,

Re: Lathe Hight

#8

Peter Charles Fagg (UK)

Re: Lathe Hight

Peter Charles Fagg (UK)

>A week or so ago John Berkeley was demonstrating at the Tudor Rose Woodturners in Daventry (UK) and his lathe was several inches above elbow height to the centre.

My own lathe is set at least 5 inches above the elbow/centre height, simply because I find it more comfortable. My lathe being a Record CL3 allows for blocks placed under the bed bar supports at either end. I will provide an image later if wanted.

Regards, Peter.

Re: Lathe Hight

#9

Re: Lathe Hight

Lester Gillett/Independence Mo

>Thanks all for the help. I have the Delta 14/42 lathe and the legs

taper down to all most a point. The hight is what i was after so

with 1" or so above my elbow i will see how that works. I like the

2x4 on each end so there is nothing to git in the way when turning.

I have some oak 2" thick i will use and if i have to i wil plane one

to git the right feel.

Lester

Re: Lathe Hight

#10

Re: One more try for the pic.

Vince

>Allen,

Hi� Vince Welch here. I recently have seen a PIC of your lathe and your shop. I also have a Oneway 1640 with the Outboard Extension and would not change a thing.

I have a question. What does your flooring consist of? 12oc, 16oc and what thickness is your plywood flooring? Do you have any vibration issues? I am considering making some changes to my shop going from concrete to wood and these are some considerations I have to deal with.

Thanks in advance, Vince