Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Good Hope Hardwoods - Walnut Slabs & Specialty Hardwood Lumber

Nova 1624/44

Posts

Nova 1624/44

#1

Nova 1624/44

Steven in the Iron Range

>Does anyone have this lathe. Looking to upgrade from a Jet mini. I like the DVR, but $2000 isn't in the budget. I can also upgrade in the future to the DVR head. Looks like a nice step up without going overboard.

Re: Nova 1624/44

#2

Love mine

Steven Kubien

>I've been turning on this lathe for around 6 months and love it. I bought mine used and the previous owner had rigged a steel shelf out of 1x2 square tubing, threaded rod and thick chain to add weight (I keep blanks and logs on it).

The lock down on the swivel headstock is very solid as is the banjo, toolrest, and tailstock. The only thing I would add if I was Nova would be a handwheel on what would be the outboard side. It would be handy, but not a necessity.

I have turned everything from pens to mounting 70lb chunks of maple for salad bowls. Since getting this lathe, I haven't turned on my mini and see no reason why I would. Whenever I decide to get a new one, I'll go straight to a Oneway 2436 or something of similar size and quality. Right now, I see NO reason to do so.

Take care,

Steve Kubien

Re: Nova 1624/44

#3

Re: Nova 1624/44

Mike Jones, Redding, CA

>Don't know if this would affect your decision, but I was unable to buy a DVR XP headstock to upgrade a Nova 3000. They say you can do it, but nobody sells them.

Re: Nova 1624/44

#4

Love mine

Steven Kubien

>I've been turning on this lathe for around 6 months and love it. I bought mine used and the previous owner had rigged a steel shelf out of 1x2 square tubing, threaded rod and thick chain to add weight (I keep blanks and logs on it).

The lock down on the swivel headstock is very solid as is the banjo, toolrest, and tailstock. The only thing I would add if I was Nova would be a handwheel on what would be the outboard side. It would be handy, but not a necessity.

I have turned everything from pens to mounting 70lb chunks of maple for salad bowls. Since getting this lathe, I haven't turned on my mini and see no reason why I would. Whenever I decide to get a new one, I'll go straight to a Oneway 2436 or something of similar size and quality. Right now, I see NO reason to do so.

Take care,

Steve Kubien

P.S. I encountered an error message when I tried to post this message. If it turns out that I have posted twice, I apologize.

Re: Nova 1624/44

#5

Re: Nova 1624/44

Mike Jones, Redding, CA

>There were no DVR heads available when I wanted to upgrade a Nova 3000. Upgrading later is not a sure thing, even though they say it is compatible for upgrade.

Re: Nova 1624/44

#6

ebd

Re: Nova 1624/44

ebd

>I've had the Nova 3k for a bunch of years and I love it. The 3k was discontinued and then a short while later they came out with the 1624. It seems to be the 3k with some improvements.

Re: Nova 1624/44

#7

Re: Nova 1624/44

Paul Vicchitto

>I have recently purchased a 1624/44.....Very nice machine! I also upgraded from the Jet Mini. Big difference! The stock leg set is not too bad. If you are planning to turn large or out of balance pieces you will need to add some ballast.I currently have about 500 lbs of sand and its running smoothly. Changing speeds is not that bad.It was not too bad to set up in my shop,you will need an extra hand as it is heavy. All in all a big upgrade in mass, precision and ease of use over the Jet Mini.

Re: Nova 1624/44

#8

Re: Nova 1624/44

john lucas

>I had the Nova 3000 and have turned on the 1624. The changes in the 1624 from the 3000 answered most of the little annoyances I had with the machine. It's a fine machine in that price range and it's a very good upgrade from a mini. Actually it's a big upgrade, you'll like it.

Re: Nova 1624/44

#9

Re: Nova 1624/44

Ed Wujciak

>I've had one for a year and love it. It does a very wide variety of things very well. I recommend it.

Re: Nova 1624/44

#10

Re: Nova 1624/44

RevDoug

>I've had it for about a year now and love it. I did add the hand wheel and the vacuum insert. Now all I have to do is work out the vac and chuck for it. I've turned 14-15" pieces with no issues. I particularly love being able to turn the headstock so that I can hollow out bowls and hollow forms without leaning over the bed. I'm also looking forward to getting a really large platter blank and turning it start to finish with the head rotated out to one side.

The only issue I have is that the legs are not adjustable enough. I had the feet all the way out and still found the spindle too low. I added 4x4's and now it is just right. For $1K I don't think you can go wrong.

Re: Nova 1624/44

#11

Re: Nova 1624/44

Ken

>I have had mine about 8 mo's and love it.Woodcraft has them on sale for 899.00 Hey a 100.00 bucks off ain't bad.

Re: Nova 1624/44

#12

Re: Nova 1624/44

Steven in the Iron Range

>Thanks guys, my mind is all but made up now.I can buy it from Woodcraft and pick it up to save on shipping. Now all I have to do is start getting blanks big enough to turn stuff bigger than pens and small bowls.