Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Rare Exotic & Domestic Hardwoods, Milled In-House in Oregon. Browse Unique Stock.

Band Saw Blades & problems *LINK*

Posts

Band Saw Blades & problems *LINK*

#1

Band Saw Blades & problems *LINK*

tek-Brunswick, Ohio

>I have a delta 14" bandsaw with a riser block. It is a closed stand 1HP. model. I still haven't found a blade that works well for a long time for roughing turning blanks from wet wood. One problem is I think the 1 HP. motor is under powered for thick blanks. I've tried the Timberwolf and Highland Blades and don't think they last much longer than the much less expensive Olsen Blades. Has anyone tried the Supercut blades? They make carbon blades and also carbide impregnated blades. I also had the front trunnion break on me and could not keep the table level. I have a new one on the way. The trunnions are cast pot metal or white metal, Whatever you call it it's weak. I'm sure the saw would hold up for less aggressive woodworking, but I am not impressed with it's quality.


SupetCut Bandsaw

Re: Band Saw Blades & problems *LINK*

#2

Re: Band Saw Blades & problems

Allen Neighbors

>I haven't tried the supercut blades. I do have a 3/4hp Sears bandsaw that I use a 3/8" 3tpi blade on. I never bog it down, but it will only cut through 6" thick. That may be why.

Re: Band Saw Blades & problems *LINK*

#3

Re: Band Saw Blades & problems

russ Fairfield

>I have used SuperCut bandsaw blades for 7 years since moving to North Idaho. My personal opinion is that they are as good as Timberwolf for less money. It helps that they are less than 5 miles up the road, but I would still use their blades if I had to order them.

I use their 3/8" X 10 TPI blade to make a saw line that is gluable without sanding, and that is something I cannot do with a similar blade from any other manufacturer, including Timberwolf.

I guess you could take this as an endorsement.

Re: Band Saw Blades & problems *LINK*

#4

Re: Band Saw Blades & problems

tek-Brunswick, Ohio

>Thanks Russ. I'll keep that 3/8" blade in mind for other work. Do you use one of their blades for roughing out green tuning blanks? If so which one?

Re: Band Saw Blades & problems *LINK*

#5

Re: Band Saw Blades & problems

Bill Clark

>I suspect you are using a fine blade with too many teeth per inch. When cutting thick material, especially if it is wet, your blade should have no more than 3 or 4 teeth per inch. When cutting thick material with a fine cut blade (6 or more teeth per inch) the saw dust from the cut has no where to go and will clog up in the teeth of a blade. This will slow your motor and cause the blade to track poorly. In wet wood the problem is magnified. The reason for a 3 or 4 teeth per inch blade is that there is plenty of room between the teeth to clear out the saw dust on a thick cut.

Re: Band Saw Blades & problems *LINK*

#6

Re: Band Saw Blades & problems

Brian Hahn in SW Wisconsin

>I also have a Delta 14" with risers. The best solution I've found is a blade with 1-1/2 teeth per inch. I haven't found one commercially, so I modify a 3 tpi 5/8" Olson blade by removing every other tooth. This blade has a three tooth pattern, so removing every second tooth preserves the pattern. There's more information about this in my band saw sharpening post on the AAW forums.

p.s. My Delta is 10 years old and handles 100 pound chunks of wood with ease.

Re: Band Saw Blades & problems *LINK*

#7

Re: Band Saw Blades & problems

tek-Brunswick, Ohio

>No, I'm using blades with 3tpi blades. They cut well when I first put them on. I cut a lot of stuff with the bark still on it. I try not to cut dirt. Once they start to get I'm bogging down the saw and having to force the cut.

Re: Band Saw Blades & problems *LINK*

#8

Re: Band Saw Blades & problems *LINK*

JohnKJordan in East TN

>tek,

Brian's method really works. (I also use a 14" Delta with riser block) I haven't seen the AAW post, but below is a link to a message on the subject he posted here a few years ago.

Steven Russell also wrote concerning bandsaw blades on 6/27/05 in the message "How to Easily Resharpen Dull Bandsaw Blades" but I didn't search for that one. (I save a file with collected bandsaw wisdom.)

JKJ


Brian's "sharpening a band saw blade" msg

Re: Band Saw Blades & problems *LINK*

#9

Here is a link to my AAW forum post  *LINK*

Brian Hahn in SW Wisconsin

>


Sharpening Band Saw Blades

Re: Band Saw Blades & problems *LINK*

#10

Re: Band Saw Blades & problems

john lucas

>You must be cutting different woods than I cut. I use a 1/2" 3 tooth blade and have cut the full depth of my saw with no problem. I have the 14 Delta with riser. In fact I cut a blank just before our club meeting the other day to have a demo piece and the guys who were there were amazed how easily my saw cut the blank. I'm using a $6 blade I get from my local saw sharpening service. I would like to have a bigger table and a brake, and a blade tensioning device but other than that it's been a good saw.

Re: Band Saw Blades & problems *LINK*

#11

Band Saw Blade Sharpening Video *LINK*

Stuart Johnson

>Here is a link to a youtube video about sharpening a band saw blade. I use this process.


Band Saw Blade Sharpening,

Re: Band Saw Blades & problems *LINK*

#12

Re: Band Saw Blade Sharpening Video

JohnKJordan in East TN

>That's about how I sharpen as well, with what looks like the same abrasive cutoff disk. However, I don't swing the dremel down on each tooth but try to just touch the side of the disk to the tooth at the right angle. Maybe that's why I'm a lot slower!

JKJ

Re: Band Saw Blades & problems *LINK*

#13

Re: Band Saw Blade Sharpening Video

Barry Irby

>I have done this and it worked fairly well, but it got me to wondering. He mentions that the orientation of the teeth is different, left right and center. I could not see that he mad any adjustment for that. He just appeared to stroke each tooth straight on. Does it matter?

And, what about making a holder of the Dremel that would get the wheel to the correct angle and just slide it forward. You could even have a stop on it to allow it to just touch the blade. Any thoughts? Am I over thinking it again?

Re: Band Saw Blades & problems *LINK*

#14

Re: Band Saw Blade Sharpening Video

JohnKJordan in East TN

>>He just appeared to stroke each tooth

>straight on. Does it matter?

I noticed that too. I defer to Brian Hahn for the answer, but if the point is angled to the left or right I try to adjust but I don't think I do a very good job. That probably slows me down too.

A device for the Dremel might be handy, but I don't know if a stop would be that useful - seems it would be hard to adjust and you might end up grinding away more than you need. I believe the professional sharpeners available for sawmill bandsaw blades also have an indexing mechanism that positions each tooth in exactly the right position - you would have to do that too or the stop would be meaningless.

JKJ

Re: Band Saw Blades & problems *LINK*

#15

Re: Band Saw Blade Sharpening Video

russ Fairfield

>As imprecise as this method of sharpening is, it doesn't matter whether we follow the set of the teeth or not. I used to follow the set until I tried the sanding disc "straight on", couldn't tell any difference, and have been doing that way ever since because it is easier and faster.

Why not try it both ways?? If there is a difference, use the one that works the best. If there isn't a differemce, then use the one that is the easiest.

Re: Band Saw Blades & problems *LINK*

#16

Re: Band Saw Blade Sharpening Video

Brian Hahn in SW Wisconsin

>I agree with Russ.

I've tried both ways. Trying to match the angle is a pain and mistakes often happen. Sharpening all of the teeth straight across is easier and faster. My experience was that flat across worked slightly better for ripping. (Also, rip saw blades are sharpened flat across.) I don't know if it is better for cross-cutting.

Re: Band Saw Blades & problems *LINK*

#17

Re: Band Saw Blade Sharpening Video

Barry Irby

>I wondered about just running the blade backwards and having them "flit" past the grinder. Either turn saw backwards by hand or turn the blade inside out and upside down so that the teeth point up (If that Is even possible), run the saw, and touch the teeth with a grinder like a Dremel, or just touch the teeth with a stone on the table like you do when you stone the back edges of the blade.

My problem is that I am running blades that cost less than $15 each. To resaw I put on a nice new sharp blade. After I hand sharpen them they never cut quite as well and I usually don't use them to resaw, particularly wider stuff. So, I have a bunch of slightly dull blades that are OK for hacking bowl blanks and thin stock. I would buy better more expensive blades, but their useful life seems so short as to make me wonder.

Russ, I have to say I was very impressed by you saying you could cut a glue joint on the edge of a piece of wood. Wow! I see people claiming to cut tenons and other fine work. I need to go back and read your article on tuning the bandsaw again. I would get a lot more use from my saw if I even though it would do work of this quality. (Its a 14" Delta with a riser block.)

Re: Band Saw Blades & problems *LINK*

#18

Re: Band Saw Blade Sharpening Video

Brian Hahn in SW Wisconsin

>I tried the stone touching the tips of the teeth as the saw ran. Very dull teeth. But I was doing it to even out the tops of the teeth (turns out to be unimportant).

I've found that the useful life of bland saw blades is related to their cost. The better / more expensive blades last longer. Also, some brands are better than others, but that really depends on what your sawing needs are. An excellent re-saw blade is not necessarily a good rough out a blank blade!