Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Veritas - Innovation in Tools

Turning related: Cleaning your bandsaw blade

Posts

Turning related: Cleaning your bandsaw blade

#1

Steven Antonucci

Turning related: Cleaning your bandsaw blade

steve antonucci

>So I cut a bunch of wet wood, and my bandsaw blade looks like it's covered in gunk. How do you folks clean them?

I've used oven cleaner on my tablesaw blades with great success, off of the saw of course...

What do you use on a bandsaw blade and on or off the saw?

Thanks in advance.

Steven

Re: Turning related: Cleaning your bandsaw blade

#2

Re: Turning related: Cleaning your bandsaw blade

Ken Oakley-Sunny St. Cloud, Fla

>The safest way I know is to remove the blade, coil it like it was when you bought it and soak it it a SIMPLE GREEN solution. I have small brass wire brushes I use to get the real stubborn stuff off.Because I am by nature lazy the following is a method I use, but am not reccommending it to the faint of heart. With the saw running I use a utility knife blade and from the rear of the saw blade I put the utility blade against the saw blade and just scrape the gunk off. DO NOT allow utility blade to come forward enough to tough the gullets of the saw blade.Then using the wire brush I remove the build up on the teeth. I also use the utility knife blade to scrape the buildup off the wheel tire. Again while running. Gotta go- The guys in the white suits are here for me.

Re: Turning related: Cleaning your bandsaw blade

#3

use PAM as you cut

fred

>i prefer the non-flavored style -- Pam keeps the sap sugars from building up on the blade

Re: Turning related: Cleaning your bandsaw blade

#4

use PAM as you cut

fred

>i prefer the non-flavored style -- Pam keeps the sap sugars from building up on the blade

Re: Turning related: Cleaning your bandsaw blade

#5

Re: Turning related: Cleaning your bandsaw blade

Jens Bingel

>I take it off the saw, coil it and clean with a brush under running warm water.

Re: Turning related: Cleaning your bandsaw blade

#6

Re: Turning related: Cleaning your bandsaw blade

Julie

>your crazy son

:)

Re: Turning related: Cleaning your bandsaw blade

#7

Re: Turning related: Cleaning your bandsaw blade

Allen Neighbors

>I've never cleaned mine. Don't know as I've ever thought it needed it.

Re: Turning related: Cleaning your bandsaw blade

#8

Re: Turning related: Cleaning your bandsaw blade

Ken Oakley-Sunny St. Cloud, Fla

>That's what being married to the same woman for 55 years will do to you.--Maybe I have a death wish.

Re: Turning related: Cleaning your bandsaw blade

#9

Steven Antonucci

When something sounds crazy to me...

steve antonucci

>you know it's crazy! I've never been cut by any spinning blade (ever!), but this sounds like a pretty good way to answer the "When was your last tetanus shot?" question.

I used a small knife, blade off the bandsaw, and some oven cleaner to get in the teeth...

Steve

Re: Turning related: Cleaning your bandsaw blade

#10

Re: Turning related: Cleaning your bandsaw blade

JohnKJordan in East TN

>>...the following is a method I use, but am

>not reccommending it to the faint of heart

I use a similar method, but instead of a utility knife I use a piece of hardwood and/or the tip of a screwdriver. Standing to the side it is certainly safer than pushing some large irregularly shaped chunk of wood into the front of the saw with your hands. This type of cleaning seems necessary or useful only when the blade is caked with heavy sap/sawdust deposits. The only danger is if the blade broke, which is no less likely than when cutting that large chunk from the front. Of course, everyone here always wears safety glasses or faceshield when doing anything on the bandsaw for that rare event when the blade breaks and goes flying toward your eyes, right?

Some may choke on this, but have I also cleaned my bandsaw mill blade with a similar method, standing behind and using a long handled tool. When cutting certain pines, the blade can build up heavy deposits of pitch after just one board, even with a continuous stream of lubrication.

JKJ

Re: Turning related: Cleaning your bandsaw blade

#11

Re: Turning related: Cleaning your bandsaw blade

Carole Valentine

>I have done that, but I don't recommend it. The only time I have done it is when I am cutting wood that gums up the blade after one pass and then I try to do it immediately (before I turn off the saw) before the deposits cool and harden. I usually use the edge of a piece of hardwood, being careful not to go as far as the gullets. Then I cut a slice of dry hardwood before going to the next green cut. The build up is really irritating. I have found that lubricants only work for a few seconds.

Re: Turning related: Cleaning your bandsaw blade

#12

Re: Turning related: Cleaning your bandsaw blade

tek-Brunswick, Ohio

>I have a couple of methods for cleaning the blade. First I cross cut a piece of Hard dry wood. That knocks off some of the loose gunk. I use a spray bottle with a Simple Green solution and a brass brush,with the saw turned off! I scrub a section and then wipe it off with a paper towel or rag. If you hold the blade still and pull the rag down toward the table it doesn't catch. If the simple green isn't getting enough I use a spray can of Advantage Cutter Cleaner. The stuff is caustic so I wear neoprene gloves when I use it. I also make sure I clean if off all the surfaces of the saw and the blade. It's kind of a pain but it pretty much gets all the crud and pitch. Maybe next time I'll take it out of the saw first. I think someone needs to make a blade for us with a nonstick coating. Has anyone tried any of the bicycle chain waxes on a blade?