Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

THE WOODRAT IS BACK!

finishing Bowls etc

Posts

finishing Bowls etc

#1

finishing Bowls etc

Julie

>I've been looking over different turners websites. Some of the bowls, etc have a shinny and others have a dull finish.

How are you all finishing your bowls?

I have seen some buff, some just use oil and some use a mixture of things.

How do you decide what type of finish to use. (except the items used for food)

Thanks in advance

Re: finishing Bowls etc

#2

Re: finishing Bowls etc

Cyril Griesbach

>Hi, Julie. I think the finish any turner uses depends on the kind of look they want on the piece. The products used may depend on the wood used and/or how the piece is intended to be used...decorative vs. functional. However, I'll go out on a limb here and say that most turners, myself included, use one of the polymerizing oils like Danish and Tung oil and some sort of buffing process such as the Beal Buffing System.

Since you've looked at a lot of turners web sites you can see the wide variety of "looks" in the finishes and probably different looks within any given turners body of work. This tends to confirm what I've said here. I'm sure that as you continue to watch the work shown here on WC that you will also learn what kind of finish was used on the pieces pictured because most of the posters will provide that information in their post. In time you will find more definitive answers to your question.

Re: finishing Bowls etc

#3

Re: finishing Bowls etc

Troy German

>To me the most important component of finishing is getting rid of all tool marks and sanding scratches. After that it's mostly preference. A few things that steer the decision are:

1) Will the piece be handled often?

2) Is there figure in the wood that should be accentuated?

3) If the wood is a light color, will the finish impart color?

4) Will it come in contact with water?

I'm still at the stage of learning the questions, so I don't feel I can give authoritative answers except to say that the material we add to the wood isn't nearly as important as getting rid of tool marks and sanding scratches.

Troy

Re: finishing Bowls etc

#4

Re: finishing Bowls etc

JohnKJordan in East TN

>Julie,

I might use a different finish depending on my mood and what the wood looks like. For example, I think wood with deep, dark, sharply contrasting figure sometimes looks better glossy since the sheen from a less glossy finish can make the blacks less black. On the other hand, some low contrast woods look better to me with a softer finish.

For small things, I usually get a glossy finish with a friction polish, applied either on the lathe or rubbed out by hand. Larger things are harder to friction polish, so I usually let multiple coats of oil dry over a week or so then buff whith the Beall buffing wheels.

For softer finishes, I might use sander sealer as a final finish and buff by hand with fine steel wool. This works with a oil finish as well. On e.red cedar I like to use beeswax since it doesn't soak into and darken the wood and it lets the cedar smell come through for a time.

I found out the hard way not to put oil on cocobolo since I had some oiled pieces turn almost black in a couple of years. This scared me away from oil for other hard exotic woods as well.

Some people I know routinely spray on lacquer and other clear finishes from a can, but I have not yet been happy with that on my turnings.

JKJ

Re: finishing Bowls etc

#5

Re: finishing Bowls etc

Mike Jones, Redding, CA

>On the left side of your screen there is a menu, highlight 'articles'

then click on "Russ' Corner". A great free resource, and enough information that it will require that you go back again and again as you gain experience.

Re: finishing Bowls etc

#6

Re: finishing Bowls etc

robert davis

>i use deft applied on the lathe. rubbed in with paper towel with lathe running.. some woods require additional spray can satin coat before buffing with beall system,...depending on the piece i may buff with scotchbrite to soften after the beall

Re: finishing Bowls etc

#7

Julie, what Mike said, plus the DVD

Ruth Niles

>I was using pretty much one finish but found different types of turnings and various woods called for different finishes. I asked opinions and that's what I got, everyone told me what they did, and that was good but I needed to learn more of what I wanted in each instance. THEN I got Russ Fairfield's "Finishing Secrets"

So from this DVD, I learned about all the finishes, how to apply them, etc. etc. Best way to learn about finishes. I can't seem to get the hang of some, like shellac chips or spraying a finish evenly. I did learn what finish results I liked best and were the easiest (probably why I liked them the best).

Mike's right, go to "Russ's Corner", there's a lot to be learned there, too.

Re: finishing Bowls etc

#8

Re: finishing Bowls etc

eliot d

>All these responses are excellent. But I bet you're looking for a straightforward formula, which most turners will tell you doesn't exist. But I,m going to try to give you one anyway: sand to 1000 grit or higher -- nothing lower than 1000 no matter what anyone says. Make sure there are absolutely no sanding scratches whatsoever. Use magnifiers if necessary. Then pick ONE type of finish, eg. tung oil or shellac-based friction pollish, whatever . the point is not to keep fooling around with everything on the shelf. Now, just wipe some on without power and then rub in with the lathe running fast so it gets too hot to hold. That's it. Then use the Beal buffing system. Done! I bet you'll love the results.

Re: finishing Bowls etc

#9

Re: finishing Bowls etc

Allen Neighbors

>For most of my turnings, except bowls, I use what I call a Lacquer Wash. It's about/approximately/somewherearound 35%Lacquer and 65%Thinner. I put on rubber gloves, and apply it with a small piece of an old Tee-shirt - lathe off. Then by the time I take off the rubber gloves and put the lid back on the wash, it's ready... I turn on the lathe, and with a clean Tee-shirt rag, I buff it until dry. Then, after it's off the lathe, I finish the bottom by hand. It'll be ready to buff with Tripoli/White Diamond/Carnauba in about half hour.

Non-utilitarian bowls get a polymerizing oil, and a buffing when cured.

Utility bowls get nothing. If a bowl is going to be used for foodstuffs, I hand out a flyer with information on how to care for it, which includes information on how much bacteria loves mineral oil.

Re: finishing Bowls etc

#10

Re: I should have said...

Allen Neighbors

>Utility bowls get nothing---except buffing. I sand them well, mostly through 400 grit, and then buff them.