Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Price drop on over 1300 Rockler items

Vari-Grind/Tru-Grind Questions

Posts

Vari-Grind/Tru-Grind Questions

#1

Vari-Grind/Tru-Grind Questions

Tom Minehan

>I have one of the early Tru-Grind Systems. I find that as the gouge flute gets shorter the tool holder must be tightened on either the transition from the round stock to the flute or on the round stock itself. Neither of these is very secure as the tool then wants to wiggle. Does the Wolverine Vari-Grind Attachment suffer the same type of problem? Could the Vari-Grind Attachment be used with the Tru-Grind base? Maybe I should learn to grind "free hand" and be done with it.

Re: Vari-Grind/Tru-Grind Questions

#2

Re: Vari-Grind/Tru-Grind Questions

Norm Smith

>Tom, The Wolverine system has the same problem. I dont know if you could use one in the other .

Norm

Re: Vari-Grind/Tru-Grind Questions

#3

Re:My solution for Vari-Grind jig.....

Jamie Donaldson

>.... and the disappearing flute problem is to grind a flat beyond the point where the flute stops and round shaft begin. This serves to index the jig on the shaft and allow accurate grinding beyond what would normally be the end of useful life of the gouges.

Re: Vari-Grind/Tru-Grind Questions

#4

Re:My solution for Vari-Grind jig.....

john lucas

>they are correct. I ground a friends gouge so the top of the non fluted area was flat. that will give him another inch or so of use. Of course when the gouge gets that short it's time for another one.

Re: Vari-Grind/Tru-Grind Questions

#5

Jamie and John, you is smart guys.

Norm Smith

>

Re: Vari-Grind/Tru-Grind Questions

#6

Dennis in Southern Oregon

Re: Vari-Grind/Tru-Grind Questions

Dennis in Southern Oregon

>Tom, instead of (or in addition to) grinding a flat on the top of the gouge, you can simply leave slightly less of the gouge protruding from the jig and readjust the setting angles slightly to compensate. You may find that you need to grind off some corners of the jig to get clearance if you carry this too far. Dennis

Re: Vari-Grind/Tru-Grind Questions

#7

Re: Vari-Grind/Tru-Grind Questions

Tom Minehan

>THANKS for the responses and simple solution!!!!! I had one of those "Gee, why didn't I think of that" moments when I read the responses. Off to the grinder!

Re: Vari-Grind/Tru-Grind Questions

#8

i also grind the top flat

robert davis

>also sometimes u can move the handle back to get more flute

Re: Vari-Grind/Tru-Grind Questions

#9

Re: Vari-Grind/Tru-Grind Questions

Lan Brady

>Tom,

I too use the the tru-grind system. You can use a one inch long piece of rod. Mine is 3/8" diameter. Lay it in the flute near to the transition. Your jig will clamp and keep the tool square. It is only a temporary solution but will give you an extra 1/2" of sharpening on your gouges.

Lan

Re: Vari-Grind/Tru-Grind Questions

#10

Re:My solution for Vari-Grind jig.....

Jennifer@Indy.USA

>My two favorite gouges have been ground flat like that too. I'm not tossing them out until they are stubs!

Jen :)

Re: Vari-Grind/Tru-Grind Questions

#11

Re: Vari-Grind/Tru-Grind Questions

Barry Turner

>Sooner or later you just have to buy a new bowl gouge. There's probably still time to let Santa know which one you would like......