Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Urban Salvaged Hardwood Slabs, Milled In-House from Rare Trees. Shop Unique Walnut Stock.

Latex for end-grain sealer: Mixed results

Posts

Latex for end-grain sealer: Mixed results

#1

Latex for end-grain sealer: Mixed results

Keith Newton

>I thought it might be a good idea to bring this subject back up with a finer focus than is normal.

There seem to be two camps. Those who say yes I have had good results, and the nay sayers.

Is it safe to assume that all latex is the same? NO

I think it would be a much better idea for whichever camp that you fall into, rather than saying something like I used latex once and lost some good wood, without making any reference to not only the kind of paint, but the kind of wood, and whether it may have gone into a kiln, or whatever drying method was used.

There are lots of variables that will have mixed results, not to mention each and all of our locations, and or the time of year etc.

Personally I have only had bad results once. That was with a big White Oak log, in August, over 110�. My mill is out on an asphalt parking lot. I was out of my usual, white latex primer. While I was at my local hardware store, I ask if they had any cheap or wrong color return that they wanted to make me a good deal on. This was not a primer, but a finish paint. When I rolled it on, I could tell that it was soaking in, rather than sealing off the surface, and even two coats was not equal to one coat of primer.

As for making a total seal against any evaporation. I don't feel that this is necessary if it slows it down enough that no checking appears. This is where those requested variables that I mentioned at the start. If you are sending a good candidate for checking through the fast drying of a kiln, I have no doubt that you would want the best. However, if you have one which can go without anything, That is another discussion.

The longer I work at this, the more experience I have to draw on, to base my decisions on, and whether we come to these forums to get advice, or because we like helping others who could benefit from our experience, the more specific one can be in asking the questions, the more specific can be the answer. Those are the ones which are most valuable.

I have some catalpa out on the lot, which has gone a year without any end-coat, yet it has no checking. I also have some cherry which will check in less than a day without anything. However if I lived in a rain-forest, it would probably be OK.

I am in Little Rock, AR, so if you have comments that contradict anything that I have offered above, I would love to learn from you whatever I can

Re: Latex for end-grain sealer: Mixed results

#2

Re: Latex for end-grain sealer: Mixed results

Wally Dickerman in Arizona

>My only question is....Why not use a wood sealer that is made specifically for sealing wood? If I have gone to the trouble and expense to gather some good wood I want to use the best product I can find to protect it.

I live in hot dry Arizona and wood cracks if not well protected.

Wally

Re: Latex for end-grain sealer: Mixed results

#3

Re: Latex for end-grain sealer: Mixed results

Keith Newton

>Wally, I agree with you. If I were where you are, I probably would do the same thing.

However, If you had cut a very fine tree, and happened to be out of anchorseal, and it would take a week to get some in during your harshest weather, what would you do?

If you chose to use a latex primer, and this kept the checks which would have started before you got the anchorseal in, do you think it would interfere with its effectiveness to follow up with anchorseal? But why bother if the latex primer works?

Have you ever used and had bad results with latex primer out there?

Oh, to answer WHY. I usually have some primer left over from other projects, so I have it on-hand which makes it virtually free.

Re: Latex for end-grain sealer: Mixed results

#4

Re: Latex for end-grain sealer: Mixed results

Barbara Gill, Remlik VA

>If I was out of Anchor Seal and needed to seal some valuable wood right away, I would heat carefully in a double boiler a beeswax toilet ring and add enough turpentine to make it thin enough to be brushed on. If I wasn't able to do that I would use oil base paint.

Re: Latex for end-grain sealer: Mixed results

#5

Re: Latex for end-grain sealer: Mixed results

Wally Dickerman in Arizona

>I have a friend who is in the wood business. He often uses paraffin heated in a large old electic frying pan for bowl blanks. Just dip the ends in the melted wax. No high heat...it has a low flash point.

Wally

Re: Latex for end-grain sealer: Mixed results

#6

Re: Latex for end-grain sealer: Mixed results

Bill Howatt

>I think this is funny. We spend big bucks on a lathe, big bucks on chucks, tools and finishes, possibly big bucks on wood or the gas to bring free wood home and we're concerned about the cost of Anchorseal to slap on the ends?

I think there needs to be a reality check somwhere along the line.

Bill

Re: Latex for end-grain sealer: Mixed results

#7

So Barbra, Waley and Bill

Keith Newton

>I understand and can appreciate that you are all sold on wax, and I am not knocking it.

I would just like to hear about your failures with latex. How did it let you down. What do I need to learn from you about its shortcomings? What am I missing?

Please fill me in on the conditions, so I will know what to avoid. Did you use a primer, or just a finish coat product, without a sealer. Did you use it early after cutting? Did you use air-drying, or was it in the kiln when things went bad, and what species?

I would just like to hear something besides Latex . XXX :-)

Re: Latex for end-grain sealer: Mixed results

#8

Re: So Barbra, Waley and Bill

Bill Howatt

>Primarily maple. Fresh cut, finish latex paint 1-2 coats, unheated but dry storage in weather ranging from hot and humid to sub-zero and dry.

My real point is that Anchorseal does a great job and so why fool around with anything else; it isn't worth the bother.

Bill

Re: Latex for end-grain sealer: Mixed results

#9

Roofing Tar works well in a pinch

Ron in Drums PA

>

Re: Latex for end-grain sealer: Mixed results

#10

There's another alternative...

Ron McKinley

>and that's woodworkers yellow glue. I was in PHX this past February for the DWR and staying with a friend. He lost a pear tree to the big freeze and said I could have it. I went to Woodworkers Source in PHX to get some Anchorseal and the biggest turning wood supplier in AZ doesn't even carry it. The manager suggested wood glue. Says it works as good as Anchorseal and is cheaper since it doesn't take much.

I cut down the pear tree and sealed the ends with yellow glue and brought it back to the CA High Desert and so far there's no checking. I would say it works. ........Ron

Re: Latex for end-grain sealer: Mixed results

#11

Ron....

Steven Kubien

>...did you thin the glue with water or apply it 'full strength'? I read somewhere once (probably on of those internet forums. Sheesh) about thinning 50/50 with water and then slapping it on. I tried it on a few pieces of ash and it worked great but on some figured maple, not so much.

Curious,

Steve Kubien

Re: Latex for end-grain sealer: Mixed results

#12

Re: Latex for end-grain sealer: Mixed results

Walter Ahlgrim

>Most latex paint is designed to be permeable by water vapor, it is a big advantage over oil base paint. Some latex is made with a vapor barrier but it is rare and expensive. Is latex as good as Anchorseal? No. Is latex better than nothing? Yes

Re: Latex for end-grain sealer: Mixed results

#13

Full Strength

Ron McKinley

>I used it full strength on the ends of the cut logs. I haven't cut them into blanks yet but the ends show no signs of checking......Ron

Re: Latex for end-grain sealer: Mixed results

#14

I Am Not Sold on Wax.

Barbara Gill, Remlik VA

>I am sold on Anchor Seal. I was responding as if my Anchor Seal had run out and I needed a substitute. I would use the beeswax/turpentine mixture in a pinch rather than latex paint. Either way I would have to go to the store and get something. Besides, the beeswax/turpentine mixture smells better. :-)

Re: Latex for end-grain sealer: Mixed results

#15

Re: Full Strength

Mike Nelson

>White glue is even cheaper, also full strength.

Re: Latex for end-grain sealer: Mixed results

#16

beeswax toilet ring

JohnKJordan in East TN

>Barbara,

I saw where you earlier referred to "beeswax toilet ring". Beeswax has gotten so expensive I had heard it was no longer used for toilet rings although most people still refer to them as beeswax and some suppliers even list them as beeswax. I looked around and found this in the book "Renovating a Bathroom" by Taunton Press:

The English, who invented what has become the modern toilet, used beeswax to seal the connection between toilet and pipe. But as the newfangled toilets gained popularity, they outstripped bees' ability to make wax. Modern wax rings are made of vegetable and petroleum waxes, with polyurethane additives.

Regardless, even those waxes should make good end grain sealers!

BTW, one reason beeswax has become less plentiful and more expensive is the way honey is processed today. It used to be the entire comb was removed and crushed and the honey strained, leaving a great deal of wax. Today, only the cappings are sliced off with a hot knife and retained for wax and most of the comb is retained in a frame for reuse by the bees next season. Before I got an extractor and started using this method, I had far more wax from my few hives. Price of beeswax varies wildly today with the , the last I checked it was around $5-$6/lb.

Today's prize for unknowingly bringing up a beekeeping topic is a free chunk of pure beeswax from the Jordan farm. Need some? It's great for woodturning!

JKJ

Re: Latex for end-grain sealer: Mixed results

#17

Re: beeswax toilet ring

Barbara Gill, Remlik VA

>That is very interesting. I was wondering why the wax was so much softer than the older rings the last time I made the belt dressing for my old planer (rosin, beeswax and turpentine). It still worked though.

Re: Latex for end-grain sealer: Mixed results

#18

Thank you gentlemen

Steven Kubien

>