Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Fast and affordable laser cutting – so you can make the parts you can’t find anywhere else

sharpening scrapers

Posts

sharpening scrapers

#1

sharpening scrapers

BQ in VT

>I just purchashed the crown tools bowl scraper with interchangable tips. What is the best way to sharpen them? I was told to hone the top face on a stone and then use a burnisher to raise a burr. I cannot get the burr right-I'm not getting one that cuts. Normally I would take a scraper to the grinder and one fast pass would do the trick. Any suggestions on how to get a good cutting edge? Thanks in advance.

Re: sharpening scrapers

#2

Re: sharpening scrapers

Wally Dickerman in Arizona

>I suggest that you forget the burnisher. Very often it's burr will be too agressive. I grind most of my scrapers at a 60 degree (30 dregrees, depending on which way you measure) angle. To give it a good burr, a 60 grit wheel or coarser is best. Most scrapers come from the manufacturer with about an 80 degree grind. It takes quite a lot of grinding to get to 60 degrees so I use a 1 inch belt sander using a 60 or 40 grit blue Zircon belt. Much faster and cooler than a grinding wheel.

Wally

Re: sharpening scrapers

#3

Re: sharpening scrapers

Wally Dickerman in Arizona

>I should add, if you're turning very hard woods, a finer grit wheel is best, to give a finer burr.

Usually, a scraper isn't used to remove a lot of wood, but is used very lightly to refine the cuts of other tools. Always go with the grain.

Wally

Re: sharpening scrapers

#4

Re: sharpening scrapers

JohnKJordan in East TN

>BQ,

I use a Tormek to sharpen Sorby multi-tip scraper blades, fairly thin interchangeable tips which I'm guessing are similiar to the Crown. (I haven't seen the Crown)

I hold the tips on a flat rest set to about 80 degrees then hone the top lightly with a diamond stone. This puts a very fine grind on the curved edges. Then I raise a "burr" with a Veritas burnisher. This is a clever little device that attaches to a flat surface and burnishes with a tungsten pin. It works especially well on large handled scrapers, using a second pin as a fulcrum allowing more force, but also works fine with the small tips. I like it better than using a hand-held burnisher since it holds the angle constant for a more uniform edge.

Compared to a burr left by a grinding wheel, this will leave an incredibly smooth cutting edge which I think lasts longer. It can be either agressive or delicate depending on how it's presented.

JKJ

Re: sharpening scrapers

#5

Re: sharpening scrapers

Brian Hahn in SW Wisconsin

>I haven't seen the Crown tools, but the Sorby multi-tip scrapers come with exactly the same sharpening instructions. It didn't take me long to decide the instructions were worthless. I sharpen them on a grinder just like any other scraper. The Sorby scrapers are a half-round cross-section which makes it very challenging to grind then free hand, so I made a holder for grinding them. I drilled an appropriate sized hole (1/4") into a piece of aluminum stock (hard wood would work as well) and added a set screw to hold the bit in place.

Re: sharpening scrapers

#6

Richard Allen

Re: sharpening scrapers

Richard Allen

>Hone the topside. This takes a bit longer than expected the first time. Inspect the honeing. Start with a coarse diamond hone. You should see scratches in the direction of honeing across the entire surface. Once you have the top scraper flat it doesn't take much to go through the finner diamond hones.

The burr can be raised with a burnishing rod, the Veritas burnisher or even with the diamond hone.

You can usually raise the burr several times between honeing.

Sharpening the next time is done with the fine hone and takes 3 or 4 passes with the hone.

These scraper tips will last for many many years when sharpened this way.

Re: sharpening scrapers

#7

Dick Hines

Re: sharpening scrapers

Dick Hines

>I sharpen my scrapers on a 60 grit wheel. I don't hone any of my turning tools. Takes to long and the first hard knot you hit will screw up the edge. When I grind my scrapers I turn them upside down on the grainding table. This gives me a nice burr. It's zip-zip and I am done.

Re: sharpening scrapers

#8

i sharpen like richard allen

robert davis

>has worked wel for me for years