Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Combination Press Plough Plane

Cutting round stock on a bandsaw

Posts

Cutting round stock on a bandsaw

#1

Cutting round stock on a bandsaw

bhenr99

>I need to cut some logs on my bandsaw and was wondering how you do it to keep the log from turning. Do you a jig or sort as I seen posts that say the blade will make the log turn during cutting. Thanks for any help.

Bob

Re: Cutting round stock on a bandsaw

#3

Re: Cutting round stock on a bandsaw

Ray Binnicker

>Hey Bob

If you don't want to "hang on tight" like Ken just said, and I've done many times, you can make a simple sled w/a runner to fit the miter slot. The sled would be 2 pieces of 3/4 plywood attached 90 deg to each other w/the runner on the bottom. Place your log on the sled, screw the log to the upright and push the whole thing thru the saw. Once you have one semi flat face you can take it off the sled and cut the rest of it in relative ease. Hope this makes sense. Sometimes I find it hard to put in words whats running around in my head.

Ray Binnicker

Re: Cutting round stock on a bandsaw

#4

Re: Cutting round stock on a bandsaw

Bill Hale / The Wood Spinner

>The right tool for the right job !

Use a chain saw.

Round stock in a band saw is just looking to break a blade and pain.

Good turning and be safe

Bill in CG, AZ.

Re: Cutting round stock on a bandsaw

#5

Re: Cutting round stock on a bandsaw

john lucas

>What Ray said is the only safe way to do it. If you try to hole a round long and run it through the blade sooner or later one will get away from you. If your lucky it will only ruin your blade. If your not lucky you could lose a finger or your whole hand. It spins really fast when it grabs. For small work I put it on the sled and hole the log carefully and feed it through. For larger logs I bolt them to the sled.

Re: Cutting round stock on a bandsaw

#6

Re:Possible loss of blade and .....

Jamie Donaldson

>.....blood! Be very careful if attempting this operation, and a nice electric chain saw for the shop would be a better alternative.

Re: Cutting round stock on a bandsaw

#7

Using a flat stick under edge?????

Stuart Johnson

>I was told once by an instructor it was safe to cut a round item if you place a thin, flat stick under the front unsupported edge. I've done that and it seems to work but it does make me nervous.

Any thought here about the safety?

Re: Cutting round stock on a bandsaw

#8

Re: Using a flat stick under edge?????

john lucas

>You would also have to put a stick under the back edge. When you start the cut it tries to rotate the log down. As you go through the cut and approach the backside it tries to rotate the long in the reverse direction. Either one is very dangerous. Even with a V shaped support fastened to a sled it will still try to do the same thing but is better supported. That's why I fasten the larger logs. The larger logs pull on the blade harder. I've had some near accidents cutting small logs using the V support without fastening.

Re: Cutting round stock on a bandsaw

#9

Don't know if it's safe or not

Carole Valentine

>but after having a small dogwood log get away from me, breaking the blade and requiring a change of underwear, I started using large wooden screw clamps - one on each side of the blade. The jaws of the clamps have a few screws going through them that protrude a tiny bit on the inside just to grip the wood a bit better. The opening (ends)of the jaws is flat against the saw table with the handles up. Tighten them down really tight. It's worked so far, but I still have a death grip on those clamps!

Re: Cutting round stock on a bandsaw

#10

The reason I like having a sawmill

Keith Newton

>is that it ellimainates that under-wear problem. :-)

Re: Cutting round stock on a bandsaw

#11

After 3 years the feeling in my finger is almost

Jerry Hall

>back. I had just gotten a haul from my first club wood cut and was working late (my wife out of town with the parting words: "Now I don't want you out in the shop late at night....")

I had a stack of nice rounds, really the first I had made. My confidence was high. The blade well used. And as I fed a round thru, supporting it well with my left hand curled under the log...

It was instantaneous. My ring finger was hamburger. Way beyond stitching. By some miracle it healed pretty well and most of the feeling is back.

I now use the electric chain saw to create a face, and usually an octagon. I find the lathe makes things round fairly well. Otherwise I use a jig and sacrificial support (that is not my fingers.)

It happens so fast, and a 3HP band saw could care less....

Re: Cutting round stock on a bandsaw

#12

Dick Hines

Re: Cutting round stock on a bandsaw

Dick Hines

>Are you talking about cutting the log cross grain? It's a good way to loose a finger or more. If you must cut a log cross grain on a band saw place a wedge under the front side of the log. Make sure you can keep it tight against the log. Cut very carefully and keep your fingers well away from the blade.

Your best bet it to buy a cheap electric chain saw.

Re: Cutting round stock on a bandsaw

#13

Re: Cutting round stock on a bandsaw

Chip in Plano

>Hot glue the heck out of it to a piece of scrap wood or plywood. If you have a circle cutting jig, you can put a hole in the carrier board, mount it on a dowel and spin it.

Also you don't really have to cut it round. I nibble the corners off around the log until it's multi-faceted. It's a lot easier and I don't have to worry about flexing the blade too much or other problems. I finish the rounding on the lathe. It can be a beating but it's not as scary

Use liberally. Glue is cheap. ER visits, copays and hand surgeon feeds are expensive (~$1500.00) DAMHIKT...but I have pictures to prove it.

Re: Cutting round stock on a bandsaw

#14

Re: I JUST HANG ON TIGHT--------

Carole Valentine

>Yeah, and one of these days, tight ain't goin' to be enough!

Re: Cutting round stock on a bandsaw

#15

Re: Cutting round stock on a bandsaw

Dennis Daudelin

>Just type, "bandsaw sled" into google and many good designs come right up! They are home made and easy to do with some scrap woods!

It's just not worth the risk!

Dennis

Re: Cutting round stock on a bandsaw

#16

Re: Cutting round stock on a bandsaw

eaglesc

>I do this all the time on a smaller scale with deer antler(irreguar shape)

Find a spot where the log wants to"rest"

Clamp it in a parallel bar clamp.

Your cut line should be on the "proud lateral side of the log.

You may need to clamp an auxilliary table on the saw.

Make the cut.

Rotate and repeat as necessary

Re: Cutting round stock on a bandsaw

#17

Steven Antonucci

It depends on how you mean it

steve antonucci

>I sometimes need to cut "round stock" or half round too.

If it's really big (pushing the limits of my 12" saw), I'll use the chainsaw. Someone else mentioned this, so I'll second it.

Sometimes, I've processed the round into half round, and drawn a circle on the flat. Mark a straight line tangential to the circle to knock off the corner and send it through the bandsaw flat side down. No danger at all with this approach, since the table supports the wood throughout the cut.

If you must cut with the round side down, I hold the wood tightly and push/pull it through the cut from the right side of the saw. I have kinked a couple of blades, but my hands are nowhere near it when it happens.

I don't worry too much about perfect circles, since one pass with the bowl gouge can take 1/2" of imperfect away in a few seconds.

Steve

P.S If you are looking to saw logs along the length into lumber, that's another story. I've seen "cradles" to use for resawing, but I don't have one.

Re: Cutting round stock on a bandsaw

#18

Re: It depends on how you mean it

Bill Hale / The Wood Spinner

>All of the above comments indicate danger. Fixes of how to lessen danger. and a potential of cuts and blood.

PLEASE PLEASE JUST DON'T DO IT.

Buy a cheap electric chain saw and keep those digits safe. A saw is cheaper than a Dr. visit and far less painful.

Please be safe, it only takes a second to do serious damage to a hand.

Bill in Casa Grande, AZ

Re: Cutting round stock on a bandsaw

#19

Re: Cutting round stock on a bandsaw

Ralph Watts

>A somewhat simple solution is to use a deep throated wood clamp. Center the pads of the clamp on the center of the log but keep the bar to the side and flat to the saw table. Screw the clamp down to the max possible--maybe even flatten a small spot on either side of the log to get a good grip. The long tail of the clamp provides a good lever and it doesn't take a lot of strength to keep the log from rolling as it is fed in on the front and out on the back..

regards, Ralph

Re: Cutting round stock on a bandsaw

#20

Solution

Tim GC

>simple solution... don't wear the underwear ....solves one of two problems!!....

Re: Cutting round stock on a bandsaw

#21

Steven Antonucci

Not at all true...

steve antonucci

>The only potential danger with a bandsaw is if you are moving your hands in the line of the cut. If you are, you may not be the brightest bulb in the chandelier...

I never have my hands anywhere near the sharp spinny things in my shop, and I've never been cut by any saw. The key is knowing what is safe, and how to minimize any potential risk.

If you have a half round log with the flat side on the table, it is no more dangerous than cutting flat stock on a bandsaw. I mention that it is my preference to use the bandsaw to knock off the corners here, since I can not see the circle (face down). I end up with a rough octagon and my circle in the middle.

If I must turn it with the round side down, it is usually to accomodate a much larger piece of wood. By standing to the right of the saw, I have at least 15" of wood between me and the side of the blade, with one hand on either side of the log and no part of my body in line with the cutting edge of the blade. I may occassionally lose a blade, but no blood gets spilled.

Given these facts, I would not recommend doing this with a small blank or unless absolutely necessary. I think it's far more dangerous to mount an unbalanced blank on the lathe than it is to use the bandsaw to trim it, but everyone needs to know their own limitations.

Steven

Re: Cutting round stock on a bandsaw

#22

Re: Cutting round stock on a bandsaw

robert davis

>make a fixture something like this


img

Re: Cutting round stock on a bandsaw

#23

Listen to John, he's right

Ruth Niles

>I used to use a wedge, usually a triangular piece of even the C shape cut off from a bowl blank. That worked good because it was flat, the one toe of the C was under the log and as the blade went through, it was cutting the C piece along with the log and nothing could slip.

Usually I use large C clamps, one on each side, you can hole the log and guide it slowly through the cut.