Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Abingdon, VA – Tree Cutting & Portable Sawmill

Revolving Stebcenter question

Posts

Revolving Stebcenter question

#1

Revolving Stebcenter question

wilbur

>I'm looking to get a live center, as I don't have one yet. I'm mainly doing spindles and using a pen mandrel. For the spindles, I thought the Revolving Stebcenter would be good.

For the pen mandrel, I understand that I should use a live center with a 60 degree point on the tail end. Can the point on the Stebcenter be used for this, or should I get a separate live center for that purpose?

If so, any suggestions on which live center with a cone tip would be good. Or maybe I should get one of those live centers with interchangeable tips?

Re: Revolving Stebcenter question

#2

Re: Revolving Stebcenter question

Bill Hale / The Wood Spinner

>If you are thinking you may want to do anything else, get a Oneway.

Get the set that has everything.

Good turning and be safe

Bill in CG, AZ.

Re: Revolving Stebcenter question

#3

Re: Revolving Stebcenter question

Ruth Harding

>Wilbur, I use my steb centre.

Re: Revolving Stebcenter question

#4

Re: Revolving Stebcenter question

Gordon Seto

>They don't seem to run as true as the Oneway or the Nova live centers. I suspect the spring load point is the reason.

Gordon

Re: Revolving Stebcenter question

#5

problem I've had...

Steven Kubien

>I have been using the live centre which came with my Nova 1624-44. Now, maybe I am exerting too much force on the live centre and pen mandrel or perhaps it is something else but I have scored the tip of the live centre pretty badly. It's not ruined and it still functions fine but I am concerned about long term use issues. Because of this, I have reserved one of my lower quality live centres for actual spindles and the Nova LC for when I am doing pens.

Probably my fault but perhaps something to keep in mind.

Steve Kubien

Ajax, Ontario

Re: Revolving Stebcenter question

#6

Re: Revolving Stebcenter question

Tim GC

>I have Stebcentres and also the Centre that came with the lathe (it is a monster piece of engineering) but I use a dedicated livecentre for my pen making. It has never been used for anything else. In fact everything I use for working pens is kept separate, smaller tools, a tool rest, assorted mandrels and livecentre.

I also have a swiveling Headstock so I do a 'kiss' test each time I use the pen making gear.

Re: Revolving Stebcenter question

#7

Re: Revolving Stebcenter question

john lucas

>I'm a big fan of the Nova live center. I have nothing but good experiences with this live center. I've had it for many years and haven't had a single problem. I've use it for everything from 60lb chunks of wood to pens.

Re: Revolving Stebcenter question

#8

JL

Re: Revolving Stebcenter question

JL

>I got a revolving Steb Centre for legs, stretchers and such to go with my drive Steb Centre. I like both a lot. I typically turn my legs first before I set them in a piece of furniture (usually a chair). I usually turn my stretchers at the same time, but I rough out the tenons.

When I have the final length for my stretchers, I remount the stretchers and put the final cut on the tenons. I find it easier to do this with a drive Steb Centre as opposed to my old spur center. The revolving Steb Centre makes it relatively easy to remount and get the same "pressure" so I don't put too much tension on the stretcher. It works better than my old Jet live center.

I have also used a Oneway live center. It also works nicely. The reason I got a revolving Steb Centre was that it was less expensive and I had a discount at the store I purchased it at. I am happy with my purchase and it met a need that I had. YMMV.

Re: Revolving Stebcenter question

#9

Stupid question on the Oneway live center

wilbur

>Is the cone that is part of the Oneway live center a 60 degree cone? Is it suitable for using on the tail end of a pen mandrel?