Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Need a tree taken down or milled?

Hambones for turning

Posts

Hambones for turning

#1

Hambones for turning

David Breth

>I spoke with a gentleman last night who has some red cedar stumps he's set aside for me. While on the phone, he asked a few turning questions, and told me his own experience from turning in the 1940's. He made baseball bats out of ash. Then he asked me about my bowls, specifically, he asked me if I boned them.

Come again?

He said when they made the bats, they would take a hambone, and press it against the bat while on the lathe, to "crush all the fibers down, so there was no cushion of air for the baseball, and it made the bats hard as H." He said when they came off the lathe, they were really smooth, and quite hard. You had to be careful not to push to hard or you could burn the wood with it, etc. Then he told me I had a lot to learn about turning, which is undoubtedly true, but I don't think I want to start doing that to my bowls.

I never heard of this technique, I'm guessing some of you who have been turning for a few decades have, but I thought it pretty interesting.

And I must say, it has taken every fiber of my being not to make coarse jokes within this post.

David B.

Re: Hambones for turning

#2

JL

Re: I thought ya'll were talking about burnishing.

JL

>the other night (Sunday). Wouldn't that be a form of burnishing?

Re: Hambones for turning

#3

Re: Hambones for turning

Jennifer@Indy.USA

>David, I don't have anything to add to this...I found it very interesting though.

Thanks for the stupid grin on my face :)

Jen

Re: Hambones for turning

#4

Re: Hambones for turning

Mike Jones

>Recently I asked here for experience with using grain fillers on very open grain wood. I had a mahogany lidded box in progress and could see that there was going to be umpteen coats of sealer, followed by umpteen coats of something to get a good finish on it.

(Trying to make this short)I wound up burnishing the entire piece with a popsicle stick to 'lay the grain down' in preparation for the finish. The burnish was all that it took to put a nice, low-sheen, hard, finish on it. I mean, it was as good as if it had a lot of tung oil coats at least, and only took a short time with little elbow grease.

Now a popsicle stick is no dadgummed hambone, I know, but then....

Re: Hambones for turning

#5

Re: Hambones for turning

robo hippy

>I remember hearing about boning before I started turning. I would agree that it is a burnishing process.

robo hippy

Re: Hambones for turning

#6

Something old-time printers would do

Ron in Drums PA

>They would score paper with a bone to help with folding.

It was also used for burnishing various items.

http://www.dickblick.com/zz129/64/

Re: Hambones for turning

#7

Re: Something old-time printers would do  *LINK*

Ron in Drums PA

>


http://www.dickblick.com/zz129/64/

Re: Hambones for turning

#8

Re: Hambones for turning

The MountainMan

>Man, when 'dat 'ole bone gat hot!! I bet it smell lik dinna' tim!!!

YA!!! HOOOOOOOOOOOOoooooooooooooooo!!!

Re: Hambones for turning

#9

You are a good man, David Breth...

Mike Jones

>Restraint under such conditions is laudable!!

Re: Hambones for turning

#10

Re: Hambones for turning

jeff myroup

>If you have access to the Summer 2007, Vol 22 No.2 issue of AAW Journal. Alan Lacer wrote a good article about the Louisville slugger Co. and it talks about bone-rubbing and flame tempering of the bats along with "powerizing". These were all tried to increase hitting. It was very interesting.

Jeff

Re: Hambones for turning

#11

As opposed to Hamboning...  *LINK*

JohnKJordan in East TN

>


Steve Hickman, master artist

Re: Hambones for turning

#12

Re: As opposed to Hamboning...

Barry Elder

>Just as people made wooden bowls before there were bowl gouges, so people did burnish wooden things before there were burnishing tools.

Re: Hambones for turning

#13

I used a dog chew-bone

Keith Newton

>to make two butterflies to bridge a shake in one of the latest turnings that I finished. Does that count? I don't know if they are Ham or bif, just dawg.

Re: Hambones for turning

#14

Re: Hambones for turning

Ken Oakley-Sunny St. Cloud, Fla.

>I have some steel rods up to 1/2" dia. which I have used for the same purpose.

Re: Hambones for turning

#15

Re: You are a good man, David Breth...

David Breth

>It was close to impossible. I still feel like going back to the orignal post and embellishing.

Re: Hambones for turning

#16

Re: You are a good man, David Breth...

Mike Jones

>Me too!