Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Urban Salvaged Hardwood Slabs, Milled In-House from Rare Trees. Shop Unique Walnut Stock.

Thompson skew

Posts

Thompson skew

#1

Thompson skew

john lucas

>I finally had time to sharpen the thompson skew that I got. I was interested to see if it would get sharp enough to use as a skew. In the back of my mind I thought powdered metal might be like carbide and not get really sharp. Well I think I proved that wrong. I sharpened it like I do my HSS tools using diamond hones followed by green compound on a leather strop.

I established the initial grind using a 100 grit white wheel. That was a little slow but the metal cuts very well. I ground it 40 degrees from bevel to bevel and the tip angle is 30 degrees.

As you can see by the photo it is quite sharp. Certainly sharp enough to be used as a skew. I won't be able to use it until later this week but I think it's going to be a great skew. The rounded bottom should roll really well and the thickness should really help it cut cleanly especially if you have to hang it over the rest. I'll let you know what I think After I turn some spindles.


img

Re: Thompson skew

#2

Bald spots

Troy German

>Do all turners have a bald spot on their forearm from testing the sharpness of their skews?

Just wondering,

Troy

Re: Thompson skew

#3

Re: Hairy bowl

Bill Hale / The Wood Spinner

>Boy that bowl has a lot of hair !

Bill

Re: Thompson skew

#4

I must have used my forehead to check sharpness

john lucas

>

Re: Thompson skew

#5

Re: Why is there only...

Allen Neighbors

>one bevel on this tool? I thought a skew had bevel's on both sides.

I'm serious. Don't know if I could even use this one with only one bevel. I've had such a hard time learning to use my others.

Re: Thompson skew

#6

Re: Bald spots

russ Fairfield

>No0 but we have determined the cause of "Woodturner Pattern Baldness" on our heads.

Re: Thompson skew

#7

One bevel, that's called a Bedan

john lucas

>Actually even the bedan has 2 bevels, it's just one is flat. It's fun to use. Watch Jean Escoulen and you will see a master with this tool.

Re: Thompson skew

#8

When confused,...

Troy German

>put the skew down before scratching your head.

Troy

Re: Thompson skew

#9

Steven Antonucci

My son says I have "Devil horns"

steve antonucci

>When they meet and I have the "Ernie from Sesame Street Haircut", I'll willingly shave the rest...

Steven

Re: Thompson skew

#10

Re: Thompson skew

Fog Tanner

>I have had and been using several of the Thompson skews for several months now (about 8 months), several 3/8" round and a 1/2" and 3/4". I use a Tormek for sharpening mine, along with my M2 skews. I use the 1000 grit surface on all my skews, and hone on the leather wheel. I will normally alternate between the stone and the hone, going to the stone only every other time. The surface has no grooves and a polished appearence. The edge will slice, not tear, through paper with a clean surface. It it doesn't then it isn't sharp.

I don't have any M2 skews as sharp as what my Thompson skews are. They are sharpened on the same stone at the same time using the same jigs and settings. All at 40 degrees with a slight radius. And the Thmpsons still come out ahead. They appear to agree with the Tormek.

I have taken to using the little 3/8 round skew for finishing cuts. I can get shavings off it that are almost like dust. The edge also stays a lot longer reducing the times to the grinder. When doing spindle work before, I would have 4 skews laid out, with one being for finish cuts only. Now I just need two and don't go to the grinder as often.

Re: Thompson skew

#11

I Never could explain the bald spot on my head

Doug Thompson near Cleveland

>

Re: Thompson skew

#12

Re: One bevel, that's called a Bedan

wilbur

>Does this method of grinding a skew give a "handedness" to the tool? I've used a skew chisel before, but not with this type of grind. It seems that it might make, say, rolling a bead in one direction easier/harder than rolling in the opposite direction.

Re: Thompson skew

#13

Re: One bevel, that's called a Bedan

john lucas

>Wilbur I haven't turned beads with the bedan in so long I can't really answer your question. I don't remember it being any easier but I'll go into the shop tonight and play and let you know.

Re: Thompson skew

#14

Thanks -- that would be great!

wilbur

>

Re: Thompson skew

#15

How many use a Bedan? Is it worth making?

Doug Thompson near Cleveland

>

Re: Thompson skew

#16

Re: How many use a Bedan? Is it worth making?

Ron McKinley

>I use one but the sharpening method recommended by Sorby doesn't work very well--diamond file across the top....Ron

Re: Thompson skew

#17

Re: How many use a Bedan? Is it worth making? *LINK*

charlie belden

>If you've got a 1/4", or 3/8" bench chisel handy, chuck up a 1/2" dowel - say in poplar

- try a single bevel. Easy to try different

bevel angle since there's not a lot of metal

to remove on a 1/4" bench chisel. Try it bevel

up and bevel down to see what works best for

you. Hell, you can use a 1/16th inch parting

tool to turn really small. And by starting with

small diameter stuff to begin with mistakes

of the learning curve won't be a big deal - no

Go Change Your Shorts type catches.

Look at this stuff and look at the tools I used

to do them.

Give it a try at a small scale with very low risk.

charlie b


Turning Small With A Bench Chisel

Re: Thompson skew

#18

Re: How many use a Bedan? Is it worth making?

JohnKJordan in East TN

>I bought one after watching a demo at our turning club, but I never learned how to use it efficiently on detail spindle work. I do find it good for flat-bottomed boxes and for some coarser cuts like sizing tenons, used like a fat, sturdy parting tool.

MHO: it would take a bedan revolution to put it on every turner's must-have list.

JKJ