Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Super Resolution Thermal Imaging Camera

How do I ....

Posts

How do I ....

#1

How do I ....

Ruth Harding

>figure out what's out of whack?

All my turnings are 1/6th out of round. Two opposite side of a bolw are i/8th while teh otehr two opposite side are 3/16th. I can see the wobble while the blank is turning and I have spent some frustrated hours trying to make blanks run true. At first I was thinking I was doing something to make it happen.

It is the same no matter which chuck I use. Interestingly - to me - is that each talon I make does not sit true in jaws either.

The only thing I can think of is the head stock spindle.

How would I know?

What should I do to fix it?

BTW, It's a Stubby.

thanks for your input.

Re: How do I ....

#2

Re: This is a real puzzle without......

Jamie Donaldson

>...some more info Ruth. Does a faceplate run true, or the body of a chuck with insert fully seated? Have you checked to see that the point of a drive spur is aligned with the point of the tailstock center?

Re: How do I ....

#3

Re: This is a real puzzle without......

Ruth Harding

>The drive spur is out a fraction, not sure how to measure it other than eyeball but it is probably in the range of 1/32. The blank seated in the chuck runs out of true. This is the same with all chucks regardless of what I am holding. Don't know about faceplate, haven't used one on this lathe.

I have put a piece of white paper behind just the chuck and ran it high and low speeds. By eyeball it looks like it's OK....how would I measure this accurately?

I guess I should also post on the stubby group site, haven't been on since I first bought the lathe,

Don't know if this info helps.

r

Re: How do I ....

#4

Re: This is a real puzzle without......

tek-Brunswick, Ohio

>Ruth, when you mount a chuck on the spindle, the chuck should seat against a shoulder on the spindle. That helps true everything up. Is there a piece of wood or crud stuck to that shoulder. That could throw things off. It also sounds like it acts like a bent spindle, but it would take some real force to bend a spindle on a Stubby.

Re: How do I ....

#5

Re: This is a real puzzle without......

Ruth Harding

>I had a look for crud but the shoulder is clear.

thanks.

Re: How do I ....

#6

Re: How do I ....

Mike Jones

>>>It is the same no matter which chuck I use. Interestingly - to me - is that each talon I make does not sit true in jaws either.<<<

If the headstock and tailstock are out of alignment, you might be making tenons that are out of whack. Refer to Stubby manual to see how to correct this. 1/32" is too much! Acceptable misalignment tolerances should not exceed .004"

Double check the jaws for gumpus and that the jaw faces are butted tight up against a true and flat shoulder on the bowl base. If Novachuck, check to see that numbered jaws match corresponding jaw slides. Check that all jaws are screwed down tight.

Check the tenon for uneven crush of the wood fiber. Make a perfect tenon with optimal diameter for the jaw set you are using.

Hope smething here helps you get back on track!

Re: How do I ....

#7

Re: How do I ....

Ruth Harding

>Thanks Mike, I will check all of these things in the morning PST.

Re: How do I ....

#8

Checking for run-out

Brian Hahn in SW Wisconsin

>Yesterday I needed to check the run-out on a chuck. This is how I did it. I set the tool rest close to the chuck body for a stable and convenient rest, then used a hard, smoothed-ended object to lightly touch the side of the chuck body. I used the end of a tommy bar, but a screwdriver would work just as well. I rotated the chuck by hand to find the high spot and held the bar so it was just touching the chuck body. Then I rotated the chuck to the low spot and checked the gap between the body and the end of the bar. In my case, the gap was less than the thickness of a sheet of paper (0.006"). I did the same thing with the jaws completely closed, measuring only against the jaw corners.

You could use the same technique to check the run-out on your spindle, just use something wide enough to span several thread tops.

Re: How do I ....

#9

Re: How do I ....

Mike Schwing from Md.

>I want to know more about these talons you are making. Threw me off for a moment or two actually!

Re: How do I ....

#10

Tenon, not talon. What kind of chuck ...

Ed Moore

>are we talking about? If it is a Talon chuck from Oneway, then I suggest that you remove the insert and clean the insert and recess. Then re-install the insert being very careful to seat it evenly. If there is a little crud or blemish between them then the chuck may not be aligned correctly. I sometimes put a LITTLE lithium grease on the insert before re-seating it. Tighten down the insert evenly and you should have good alignment.

Have you cleaned out the Morse tapers on the headstock and tailstock? Crud can accumulate there and cause the centers to be misaligned.

After doing all the above, turn a tenon on each end of a short piece of dry wood with the grain parallel to the ways of the lathe and turn a cylinder. Cut the shoulders carefully/square with a skew. Then insert this piece into the chuck. Make sure that the shoulders seat against the jaws of the chuck and that the end of the tenon isn't touching the bottom of the jaws. Check this piece to see if it runs true. True up the side of the cylinder on the end closest to the tailstock with a skew or parting tool. Loosen the chuck and rotate the piece a quarter turn and re-tighten. Does this run true? Loosen and rotate another quarter turn. Does this run true? Any alignment problems should appear now.

Ed

Re: How do I ....

#11

Re:As a Stubby owner(Studly!) and ...

JamieD

>.. long time user, the only thing that I have ever known to cause a potential out of alignment problem is a lathe not sitting square on the floor. It is possible to torque just about any lathe bed by inaccurate leveling, and the adjustable Stubby legs are usually the cure if properly adjusted, easily accomplished with a jack.

Re: How do I ....

#12

Re: How do I ....

Ed Wujciak

>From what you say, it almost sounds like the bowl is warping BETWEEN the time when you turn the outside and when you turn the inside. That is one way that you can have different rim thickness 12 & 6 versus 3 & 9 o'clock. DAMHIKT

Re: How do I ....

#13

Re: Checking for run-out

Ruth Harding

>Thanks Brian, you explained it perfectly.

r

Re: How do I ....

#14

talon/tenon

Ruth Harding

>I guess it was either OA catching up or the lateness of the hour. But then again it could have been the 2nd glass of wine.

:)

I will try everything recommended and get back to you later in the day. Thanks for the good tips.

r

Re: How do I ....

#15

Update

Ruth Harding

>I think I had not cut enough off the protruding bit from turning between centres and it was catching between the jaws: (never thought of that, thanks Mike Cunningham). I also had a bit of gunk here and there on the jaw teeth. Although each bit looked insignificant, all together it could have been enough to throw it out of true.

I lined up a steel ruler with the side of the chuck and found that it is running true.

I also wedged underneath the corner that isn't bolted to the lathe because the hole didn't line up. There was certainly a gap there between the lathe and the stand.

I cleaned everything, the jaws, the chuck, the spindle shoulder, the spur centre......

I am hoping that all of this did the trick. Unfortunately I didn't have any time to turn anything today to find out for sure.

Thanks for all your tips and suggestions.

r

Re: How do I ....

#16

Re: Ruth- a last bit of advice about....

JamieD

>... bolting down the Stubby bed to the stand, and this would be true for other brands as well. I put a split lock washer between flat washers under the head of the Allan head bolt before screwing it down moderately tight. This gives sufficient tension without the chance of torquing the bed assembly or even cracking the casting. And Studly ain't going nowhere nohow! ;-)))

Re: How do I ....

#17

Re: How do I .... *LINK*

russ Fairfield

>While we often are quick to blame the chuck or the lathe, there are a lot of other things that can influence how true a piece of wood tracks when we clamp it in a chuck, from the wood itself, to the orientation of the grain and how hard we squeeze it. You might look at the following article on using chucks, and see if there is something there that might help.


Tips on using a chuck

Re: How do I ....

#18

Re: How do I ....

Ruth Harding

>Thanks Jamie.

Russ, fabulous information. Looking forward to seeing your pen site finished.

r