Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Price drop on over 1300 Rockler items

DITIGAL CALIPERS

Posts

DITIGAL CALIPERS

#1

DITIGAL CALIPERS

Dennis Taylor

>I picked up a digital caliper from HF yesterday, looks just like the one in the Craft Supply catalog, but 1/2 the price...the ends are pretty sharp, should those be grounded round & smooth?....not used any calipers before, just eye ball, but wanted a pair for a while now...any caliper usage tips needed?...Dennis

Re: DITIGAL CALIPERS

#2

JL

Re: DITIGAL CALIPERS

JL

>I use my "analog" dial calipers pretty often to size tenons. I naven't rounded them off. As they are a precision measuring device, I'd rather leave them as they were made. I do check the accuracy and precision fairly often.

That being said, I have rounded off my spring calipers that I use for rough sizing. If these are digital, they may have a zeroing capability so that they can be re-zeroed if you decide to round them off. If yours have this capability, you could probably do round them without messing up your precision and accuracy.

Re: DITIGAL CALIPERS

#3

Re: DITIGAL CALIPERS

Ralph

>Some months back I was talking to XXXXXX at a show, and remarked that the digital calipers he was selling looked just like the HF ones I have. his response was "...well, that's where I buy the ones I resell.."

Re: DITIGAL CALIPERS

#4

Re: DITIGAL CALIPERS

Brian Hahn in SW Wisconsin

>Digital and dial calipers are machinists calipers and the sharpness that you are noticing is there because it is needed for making accurate measurements. I don't round those edges because I need them for precise measurements. However, they are your calipers and you can round them if you want to.

Re: DITIGAL CALIPERS

#5

Richard Allen

Re: DITIGAL CALIPERS

Richard Allen

>I got a set of cheap digital calipers. The are easy to read!! They also go through batteries quickly. You can buy batteries on-line and when you do that the cost is low but the shipping is not low. So buying 5+ batteries makes the shipping less of a burden.

Rounding? I wouldn't.

Re: DITIGAL CALIPERS

#6

Re: DITIGAL CALIPERS

JohnKJordan in East TN

>Dennis,

I keep several digital calipers for careful measuring and several cheap non-digital calipers for turning to size. I prefer to keep the points on the digital calipers sharp and keep them in cases for protection.

However, I round off the points on the cheap calipers so they will slip over a spindle while it is turning. These are very inexpensive vernier calipers from Home Depot and hardware stores which get rough handling rather than careful protection. I seldom use these for measuring anything - most turning doesn't seem to need accurate measurements but repeatable sizing for duplicating diameters.

JKJ

Re: DITIGAL CALIPERS

#7

Re: DITIGAL CALIPERS

Sonja Lemon

>We've picked up batteries from the $ Store -- 10 for $1.00! Can't beat that price. (357A - 1.5V)

Re: DITIGAL CALIPERS

#8

digital calipers and batteries

JohnKJordan in East TN

>>I got a set of cheap digital calipers....

>They also go through batteries quickly.

I wondered if anyone else had that experience. I've got four different digital calipers. The cheapest one (from Woodcraft) will run through batteries in a few months even if the thing is resting unused in a drawer most of the time - I'm about ready to throw it away.

The batteries seem to last far longer on the better calipers. Just last week I replaced the battery on the one I use the most (a 6") after about at least 5 years of heavy use. I have another higher quality digital caliper (a Mitutoyo, good to .0005" in 8") I've used for over 15 years and never changed the battery. (This one has a data port for connecting to a computer - who would use that in a woodshop!)

JKJ