Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

THE WOODRAT IS BACK!

next step - do the bottom!

Posts

next step - do the bottom!

#1

next step - do the bottom!

Carol Reed - in Nebraska

>Thanks for the help with the scratches. Wally reminded me about shear scraping with the bowl gouge after waxing. That did it. Made me nervous though! I gotta get back to Arizona for another lesson! That'll take a year!!

Now I need to do the bottom. No 'jam' chuck. No Longworth. No vacuum chuck. The bowl is nearly 9 inches in diameter. Almost hits the ways!

My thought (with regard to what I have on hand): Mount a piece of plywood on a face plate, after cutting it round on the band saw. Stick on a WalMart Sticky Foamie. Bring up the tailstock with the live center. Light cuts only.

The question is how to get it centered!

Other suggestions very welcome.

Also, I bagged the bowl as Wally suggested. I think I will lacquer it, as oil makes it darker than I'd like. Should I do that to the inside and outside before I finish the bottom, or wait until the whole bowl is done? Also have to get to the auto parts store next week and get some finer sandpaper. I only had up to 320. I know, I know, order some from Vince.

I'd do pictures, but my desktop PC crashed and I don't have the camera software on the laptop. Need a new drive and complete re-install. Bummer big time. So I am making sawdust to keep from screaming!

Re: next step - do the bottom!

#2

Re: next step - do the bottom!

Jim Swank

>I prefer to put a coat or two of lacquer (or sealer and lacquer) on before turning the bottom, then final coats on after. That seems to protect the rim a little beter during any kind of reverse chucking, but the final coats on the piece as a whole eliminates any disconnect between body and bottom.

Re: next step - do the bottom!

#3

Re: next step - do the bottom!

Jim Swank

>PS. You can center it pretty well by eye. Use a pad or block of hardwood between live center and bottom until you get it spinning justt ight. The stop, hold bowl in place with left hand, retract tailstock & remove block, re-extend tailstock to hold bowl, and you're set.

If you start between centers, you'll have a mark. You can also add one if you're turning rough, the drying and re-turning, or figure where and how to do this in the future. DAMHIKT. :)

Re: next step - do the bottom!

#4

Re: next step - do the bottom!

Doug Turner

>Carol,

I use a piece of round plywood, mdf, particle board etc mounted to a faceplate and cover the "wood" with a layer of glued on naugahide. I place the tool rest in front of the naugahide covered wood and draw circles with a permanent marker every 1/2". Now when you are centering your bowl you have a guide. As a bonus the naugahide grips the wood and doesn't leave marks. John Jordan showed me this 20 years ago.

Re: next step - do the bottom!

#5

Re: woodcraft beginner's turning set a good buy? *LINK*

Rick Urban

>Hi Carol... I've made/tried compression chucks... I had cole jaws... I sometimes use my "potter's wheel" on the spindle... I have a vacuum chuck... It's nice when you can have unfettered access to the bottom, but I still go between centers a lot... Some say ALWAYS leave the tenon on after completely finishing the rest. I have come to prefer to completely finish the piece before the first topcoat application (usually lacquer for art pieces).

I use a well padded "turned and trued stump" in my chuck with the tailstock live center in the original position still marked from the when the tenon (or recess) was cleaned up for final turning. (This avoids the problem associated with a bowl that has moved since finishing that won't sit straight on the flat turntable you are using.) When you can't have complete access to the bottom you can leave a very small nub with this technique that is not a big problem to deal with using something like a dremel tool or hand sanding. Some turners I know like to manually carve it away in a manner that further "signs" their work. There are a lot of techniques out there. The hard part is deciding which one(s) you like.


img

Wood You Believe

Re: next step - do the bottom!

#6

Oops!

Rick Urban

>Oops! Sorry about that. I sure didn't mean to put all the rest of that stuff in there. Guess it's obvious I haven't been a regular enough contributor to know about all the switches.

Re: next step - do the bottom!

#7

Re: next step - do the bottom!

Darryl

>You can also use the stuff they use under carpets. cheeeep if you have a carpet installer around and can get into their trash bin. Put the bowl against the faceplate or your chuck covered with the pad. Bring your tailstock up lightly. Put your toolrest so the edge is at the level of your tailstock center. Bring the tool rest close to the bowl. Rotate the bowl slowly by hand and when you see it is out of round loosen the tailstock slightly and move the bowl edge half the distance from the toolrest to the opposite side. Then rotate again. A couple of passes and you'll have the bowl centered. Then tighten the tailstock. If you get a tailstock with a cup rather than the point it will not leave as much of a dent. Turn the bottom with an edge or whatever. Then cut down to the point of the tailstock and part off or simply and the nubbin that is left. Works.

Re: next step - do the bottom!

#8

Depends on the shape of the top

Don Henthorn Kyle, Texas

>of the bowl, but you could screw another hunk of plywood to the piece you already have attached to the face place. Then turn the second piece down so it just fits inside the top of your bowl. Now bring the tail stock up and the bowl should be pretty well centered.

Re: next step - do the bottom!

#9

Peter Charles Fagg (UK)

Re: next step - do the bottom!

Peter Charles Fagg (UK)

>Carol, forgive me if I am wrong but..........

You wrote: My thought (with regard to what I have on hand): Mount a piece of plywood on a face plate, after cutting it round on the band saw. Stick on a WalMart Sticky Foamie. Bring up the tailstock with the live center. Light cuts only.

May I suggest that you turn it to the correct size rather than cutting on the bandsaw, it will then be centred, and if you leave it mounted, then gentle pressure with a cup centre in your tailstock will enable you to turn away most of the bottom. The piece usually finds its own centre by merely turning it by hand as you tension the tailstock screw.

Regards, Peter.

Re: next step - do the bottom!

#10

Peter Charles Fagg (UK)

Re: next step - do the bottom!

Peter Charles Fagg (UK)

>I forgot to say that with care a piece of cloth can be used as a friction drive inside the bowl but overflowing the ply disc only slightly.

Regards, Peter.

Re: next step - do the bottom!

#11

Re: next step - do the bottom!

Carol Reed - in Nebraska

>Thanks, Peter.

I think what you ean by the 'correct' size is a diameter slightly smaller that the inside rim diameter and then a cloth to protect the inside of the bowl. Maybe with a slightly tapered edge to fit inside the bowl? Sort of a large jam chuck? That's a thought.

I am moving this weekend, so this project will stay bagged on the lathe for a while. I won't have time to return to it for maybe two weeks. Sighhh....