Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Abingdon, VA – Tree Cutting & Portable Sawmill

DIY - faceplate caliper - cheap & best I've used

Posts

DIY - faceplate caliper - cheap & best I've used

#1

ebd

DIY - faceplate caliper - cheap & best I've used

ebd

>The following set of postings illustrates and describes how to make the most useful caliper for faceplate work that I have used. If you buy it from a catalog they cost $50 plus shipping. There's also something that recently came out that works on the same principal but costs $70 plus shipping. If you make the one described below it costs about $5 if you use brass rod and less than $3 if you use steel rod. Everything can be found in any hardware store. You can modify the plan to make it custom suited for very wide flatish turnings (big plates & platters) or very deep narrow turnings with small openings (hollow forms). You can make it as big or small as you want. It takes less than a half hour to put together.

Materials list:

3 feet of 3/16" brass ($4.49) or steel rod ($1.79)

1 cable ferrule ($0.49)

2 drops of thin CA glue (nominal)

Hint: When you get to the hardware store grab the rod first. Then check to make sure that it slides through both holes of the ferrule. These parts aren't machined to fine tolerences.

NOTE 1: In case you don't know what a cable ferrule is - its a coupling used to make an end loop in wire rope. You pass the wire rope through one channel and back through the other in the opposite direction, leaving the size loop that you want. You then crimp the ferrule to hold the wire rope. A picture of a cable ferrule is below.

Note 2: All bends described are made in the same plane. In other words the bent rod always lies flat.

Note 3: Please don't take offense at the detail. I realize most of you could do it from the pictures alone. The detail is for those who might need it.

Step by step instructions are in the following posts, along with photos.


img

Re: DIY - faceplate caliper - cheap & best I've used

#2

ebd

Re: DIY - faceplate caliper - part 1

ebd

>1. Take the rod and bend it to 90 degrees about 1 1/4" from one end. A vise is very handy for this but it can be done with vice grips or heavy pliers.

2. Bend an approximate semicircle ending up with the straight portion of the rod at 90 degrees to the original bend. This bend can be easily done by hand.

See picture below.


img

Re: DIY - faceplate caliper - cheap & best I've used

#3

ebd

Re: DIY - faceplate caliper - part 2

ebd

>3. Line up a square and make sure that the bend is at a clear 90 degrees and mark the straight portion of the rod (opposite the first bend) where the straight edge crosses.

4. Bend the rod at 90 degrees back toward the first bend.

5. Tweak the bends to get the first bend and the return bend to lie parallel and just touch.

6. Once you get everything bent, dry fit the ferrule.

See picture below.


img

Re: DIY - faceplate caliper - cheap & best I've used

#4

ebd

Re: DIY - faceplate caliper - part 3

ebd

>7. Put a mark on the return bend where you want the caliper points to meet.

8. Cut the rod with a hacksaw on the mark.

9. Remove the freed straight section of rod. Grind both cut ends roughly spherical (round off the cut ends to smooth them and give a more or less single contact point).

See picture below.


img

Re: DIY - faceplate caliper - cheap & best I've used

#5

ebd

Re: DIY - faceplate caliper - part 5

ebd

>10. Position the ferrule on the first bend with the open ferrule chamber up and make sure that the ferrule is in the same plane as all the bends. Put a drop of thin CA on the lower side of the the rod that is through the ferrule (on both sides of the ferrule). The CA will be drawn into the ferrule by capillary action.

Note: You could also hammer the side of the ferrule that holds the first bend. I did that with the first one I made. I find the CA to be easier and look better.

Note: You want the part of the ferrule that's going to house the sliding rod on top so you minimize any leakage of CA into it.

11. Once the CA has set. Saw off the excess part of the first bend that sticks out of the ferrule (on the side where the sliding rod will be inserted).

12. With a 3/16" drill carefully "size" the open part of the ferrule to clear any burrs or CA that might have leaked in.

13. Sand the straight rod with about 100 or 120 grit sandpaper. Lubricate the straight rod with something. You could use paste wax, Armor-All, Graphite, etc. I'm partial to Pedro's Extra Dry Chain Lubricant (it's used for mountain bike chains).

14. Insert the rod and tweak everything till you get a good point to point contact.

15. At this point you can either do as I do and find a rubber cap, some rubber hose, or some old aquarium hose with the right inside diameter and push it over the outside of the sliding rod all the way up to the ferrule so it touches when the caliper points touch. I do it this way so I can "re-calibrate", if necessary, in the future. Other alternatives are to wrap tape around the rod at the ferrule, or mark a scale on the rod with a triangular file. I'm not Obsessive/Compulsive and seeing that the thickness is about 1/4" is good enough for me. I don't need to know that it's really 9/32". Beside, if I really want to know I can measure the gap with a ruler.

See picture below.


img

Re: DIY - faceplate caliper - cheap & best I've used

#6

ebd

Re: DIY - faceplate caliper - use for side

ebd

>This picture shows the caliper being used to measure the side thickness.

Note: This (obviously) can be done while on the lathe as well.


img

Re: DIY - faceplate caliper - cheap & best I've used

#7

ebd

Re: DIY - faceplate caliper - use for bottom

ebd

>This picture shows the caliper being used to measure bottom thickness.

Note: Perhaps not so obviously, this can also be done while the bowl is on the chuck by working through the gap in the jaws.


img

Re: DIY - faceplate caliper - cheap & best I've used

#8

ebd

Re: DIY - faceplate caliper - use while chucked

ebd

>This picture shows the caliper being used to determine bottom thickness of a reverse chucked bowl working through spaces in the Cole jaws.


img

Re: DIY - faceplate caliper - cheap & best I've used

#9

ebd

Sorry - part 5 should be part 4

ebd

>

Re: DIY - faceplate caliper - cheap & best I've used

#10

Very Nice!

Gary in Zirconia,NC

>

Re: DIY - faceplate caliper - cheap & best I've used

#11

Re: DIY - faceplate caliper - cheap & best I've us

tek-Brunswick, Ohio

>Thanks that is a great idea! That should go into the article section.

Now I need to take a trip to the hardware store.

Re: DIY - faceplate caliper - cheap & best I've used

#12

Steven Antonucci

I have to make a couple of those!

steve antonucci

>I'm getting to the point where I realize that there may not be a single tool for every measurement, and I love the direct measurement on the back end. I'll probably turn a little fancy finial for mine instead of the rubber nib, but this is a great tool.

Thanks for posting.

Steve

Re: DIY - faceplate caliper - cheap & best I've used

#13

Thank you. Excellent idea.

adrien

>

Re: DIY - faceplate caliper - cheap & best I've used

#14

Re: DIY - faceplate caliper - cheap & best I've us

Lan Brady

>great article , thanks for posting

Lan

Re: DIY - faceplate caliper - cheap & best I've used

#15

Re: DIY - faceplate caliper - cheap & best I've us

eliot d

>I'd like to copy a picture of your caliper, but I can't figure out how to do it. If I try to print the page, I just get written stuff. Do you know how to copy the picture?

Re: DIY - faceplate caliper - cheap & best I've used

#16

Re: DIY - faceplate caliper - cheap & best I've us

Allen Neighbors

>Absolutely excellent tutorial on how to make this caliper (or should I say 'these calipers').

I'll bet woodturners all around the world will have some of these before a week goes by.

Thanks for taking the time and energy. I appreciate it.

Re: DIY - faceplate caliper - cheap & best I've used

#17

Re: Eliot, RIGHT Click the pic...

Allen Neighbors

>you'll get a dialog box that has a lot of options on it.

Click SAVE PICTURE AS.

And save it where you want it. I usually put things on my desktop, so I can gather them together and put them into a document.

Need more info? Email me. :)

Re: DIY - faceplate caliper - cheap & best I've used

#18

Thank You- Great For Article Section

Barbara Gill, Remlik VA

>

Re: DIY - faceplate caliper - cheap & best I've used

#19

ebd

Re: DIY - faceplate caliper - cheap & best I've us

ebd

>Simple. Just Right click on the picture and choose "Save Picture as".

Re: DIY - faceplate caliper - cheap & best I've used

#20

Fabulous stuff. Thanks!

Steven Kubien

>

Re: DIY - faceplate caliper - cheap & best I've used

#21

Excellent! Thanks

Ron McKinley

>