Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Nearly 100 Exotic Wood Species, Direct-Imported Since 1972. Shop Slabs & Turning Stock.

Camphor burl vase....

Posts

Camphor burl vase....

#1

Mike Stafford

Camphor burl vase....

Mike Stafford

>I know it is not a box! I have had this piece of wood for quite a while and I have wondered how I was going to turn it. Finally I decided to try. It is turned end grain wise and I used my Sorby multi-tool and my Hunter Tools in conjunction with a box rest so I had extended reach inside the bowl. It is about 1/8" thick at the rim and thickens to about 1/4" at the bottom.

I have always been fond of the "snifter" form and I don't know if I got it right or not. I left the inside sanded smooth but unfinished except for the top inch or so. The smell from the camphor permeates the display case.

This piece is 5" in height and 5 1/2" in diameter. Comments appreciated....


img

Re: Camphor burl vase....

#2

Mike Stafford

Ruth, it is camphor burl.... ;>))

Mike Stafford

>

Re: Camphor burl vase....

#3

JL

Re: I like it. Could you rotate it 90 degrees?

JL

>I'd like to see the rest of the grain pattern. I though camphor was a bit lighter - or is it that it is a burl?

Re: Camphor burl vase....

#4

Mike Stafford

Re: I like it. Could you rotate it 90 degrees?

Mike Stafford

>Jerome, it is a piece of burl. But to allay your suspicions I did photograph the side with the most figure. This piece may have darkened a little due to the oil/varnish finish I used.


img

Re: Camphor burl vase....

#5

Steven Antonucci

Pretty piece of wood

steve antonucci

>I like the form too, especially the little inward turned rim. Subtle, but completely in line with a real snifter.

Makes me wish I liked brandy.

Steve

Re: Camphor burl vase....

#6

Juicy!

Jennifer@Indy.USA

>I love it Mike. The wood isn't too shabby either!

Jen

Re: Camphor burl vase....

#7

Re: Ruth, it is camphor burl.... ;>))

Barbara Gill, Remlik VA

>Mike that sure is pretty.

Re: Camphor burl vase....

#8

Re: What, no lid!!!! ;-))) Nice!!!

Jamie Donaldson

>

Re: Camphor burl vase....

#9

JL

Re: Nice "flame"!

JL

>I really like the red "highlights".

Re: Camphor burl vase....

#10

Re: Camphor burl vase....

Ken Oakley-Sunny St. Cloud, Fla

>I love the smell of freshly cut camphor and luckily it grows everywhere here in Fla. Many times I have to decline offers of logs of it because I have so much of it.

I will cut or sand some just to make the shop smell better.

Re: Camphor burl vase....

#11

Mike Stafford

Re: Camphor burl vase....

Mike Stafford

>Ken, it must be nice to have that problem....

Re: Camphor burl vase....

#12

ROFL!

Carole Valentine

>Poor Ruth!:)

Looks perfect to me Mike. I like that form too. I have made a couple as pencil holders for people.

Re: Camphor burl vase....

#13

Re: Camphor burl vase....

Jim Terry

>Very nice Mike, I like the form and it is also a nice piece of wood

Re: Camphor burl vase....

#14

Very Nice, but a familar form

David Propst

>Hi Mike,

I like that form, I bet the wood shimmers in real life.

I have a similarly shaped piece prominently displayed in my "collection", you may owe Bill Grumbine a reproduction fee. ;-)

Missing turning time,

David

Re: Camphor burl vase....

#15

Re: Mike, a box rest?

Allen Neighbors

>I guess I've never seen one, or heard of it either. Unless it's what my old shop teacher called a 'pin-rest'. Can you explain what it is, or post a pic of it?

"For extended reach inside"... sounds like a small "L"-shaped gizmo... am I right?

Re: Camphor burl vase....

#16

Mike Stafford

Tell Bill the check is in the mail...

Mike Stafford

>I wouldn't dare infringe on the lathelectual property of Mr. Grumbine.

Re: Camphor burl vase....

#17

Mike Stafford

Re: Mike, a box rest?

Mike Stafford

>Yes, Allen, it is a flat piece of steel that attaches to the tool rest post and can be inserted into the opening of a box to provide support closer to the point where you are cutting. Mine is about 1 1/2" wide and 4" long.

I am sorry I don't have a picture.

Re: Camphor burl vase....

#18

Re: Ruth, it is camphor burl.... ;>))

Ruth Niles

>Thanks, Mike. You notice I didn't respond right away, I had to be sure I read everything right.

I love this form and the grain in the boxelder looks great, I love the lid but the finial is a tad too fat.

Seriously, I really do like the form and you did a great job.

Re: Camphor burl vase....

#19

Re: Mike, a box rest?

Mike Brazeau

>Alan - The one on the right is one I made a couple of years ago for my 2436 from bits of cold rolled steel I got out of the shorts box at Metals Supermarket. My neighbour has a small wire welder and loves to use it. They were a simple butt joint with a hole centered over the stem which he filled in and I ground off. I cut the steel and shape as necessary and he welds. Needless to say, a good neighbour to have.


img

Re: Camphor burl vase....

#20

Mike Stafford

You are a good sport!!!

Mike Stafford

>

Re: Camphor burl vase....

#21

Re: Mike and Mike, Thanks.

Allen Neighbors

>Can you give me a little instruction now? Do you lay your tool on it with the tool shaft making contact all along the length of the box rest? Or do you angle your tool across it?

After thinking about it, I guess you do whichever works at the moment?

Thanks, for your help, Gentlemen, I appreciate it.

Re: Camphor burl vase....

#22

Mike Stafford

Re: Mike and Mike, Thanks.

Mike Stafford

>When I use a scraper with the box rest I angle it downward a little just like I would with any other tool rest. Same for the Hunter Tool although I doubt it was designed to be used with a box rest. I was just using the box rest to shorten the reach of the tool and allow me to get farther into the vase.

Adapt and overcome.....

Re: Camphor burl vase....

#23

Re: Mike, a box rest?

Lan Brady

>Great job Mike!

Lan

Re: Camphor burl vase....

#24

Re: Mike, a box rest?

Dennis Yoder

>Allen, on page 34 of the new Craft Supply catalog there is a picture of one. Denni Y

Re: Camphor burl vase....

#25

Re: Thanks, Dennis :)

Allen Neighbors

>