Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Precision you can feel — woodworking perfected with Lee Valley

drawbar thingies

Posts

drawbar thingies

#1

drawbar thingies

Carol Reed - in Nebraska

>This is a mystery to me. Could somebody post pictures of drawbar chucks, drives, whatever, and show how this "drawbar" thing works. My head just doesn't have a picture.

The only drawbar knowledge in my poor little pea brain is the drawbar hitch on a farm tractor! :)

Re: drawbar thingies

#2

Re: drawbar thingies

Carole Valentine

>Picture a drill chuck with a threaded hole in the MT end. Screw a piece of threaded rod into the MT, insert the MT with the rod though the hollow tailstock (or spindle) and put a nut (I use a wing nut) on the end of the rod that extends out of the tailstock and tighten it down to draw the MT tight and prevent it from spinning out.

Re: drawbar thingies

#3

Re: drawbar thingies

Mike Schwing from Md.

>I didn't even know mine was threaded till I was working with Chris Keuhn at my house, the drill chuck fell out, and he asked me why I hadn't had a drawbar. Doh!

Re: drawbar thingies

#4

Re: drawbar thingies

adrien

>this what you're looking for? the rod is threaded


img

Re: drawbar thingies

#5

Drawbar Picture (link) 

Gil Jones

>


img

Re: drawbar thingies

#6

Well, that link did not work. *LINK*

Gil Jones

>http://www.sherline.com/3072inst.htm


http://www.sherline.com/3072inst.htm

Re: drawbar thingies

#7

Re: drawbar thingies

Robin Corell, in Atascadero CA

>A draw bar can certainly be added to a drill chuck, but the term is usually used to describe a chuck that more closely resembles a router collet and is tightened with a bolt on the out board side of the head stock. The machinist versions are generally sized to hold a very narrow range of round stock. The wood lathe versions are some what more versatile.

Robin

Re: drawbar thingies

#8

Re: I don't think drawbars work on most tailstocks

Al Crandall

>The majority of tailstocks are designed such that the handwheel, while being turned, stays stationary relative to the work and the inboard end of the tailstock spindle advances toward the work. If there is a chuck and drawbar installed you won't be able to turn the handwheel. Drawbars work much better when used in conjunction with headstock spindles or on lathes like my first tube bed which had a drive wheel in the middle of the spindle so the whole spindle advanced toward the the work.

Re: drawbar thingies

#9

Why use a drawbar in the tailstock?

keith zimmerman, Normal, IL

>There should be no reason to use a drawbar in the tailstock because it doesn't move. Friction should hold the MT of a drill chick in place for any action to be done. A drawbar is definitely beneficial when using a drill chuck in the headstock though.

keithz

Re: drawbar thingies

#10

Re: Why use a drawbar in the tailstock?

Carole Valentine

>I have one in my buffing wheel on the mini. That's the only time I use a draw bar in the tailstock. The male taper is not quite perfect on my Beale system.

Re: drawbar thingies

#11

Duh! That's in the headstock too!

Carole Valentine

>Don't know what I was thinking.

Re: drawbar thingies

#12

We all have moments like that.

keith zimmerman, Normal, IL

>

Re: drawbar thingies

#13

Re: We all have moments like that.

Don in Central Illinois

>And the older I get, the closer together they get.

Re: drawbar thingies

#14

Re: We all have moments like that.

Carole Valentine

>I seem to be having more than my share lately! :((

Re: drawbar thingies

#15

Re: We all have moments like that.

Barry Irby

>If you are using your chuck in the tail stock to drill a hole in difficult wood, the drawbar can be useful when backing the bit out. I usually just hold the chuck itself and pull while backing it out, but if it releases on the taper with the lathe running it could be exciting.

Re: drawbar thingies

#16

Re: We all have moments like that.

eaglesc

>" but if it releases on the taper with the lathe running it could be exciting."

Yep.DAMHIKT

Re: drawbar thingies

#17

Re: drawbar thingies - OK, but...

Carol Reed - in Nebraska

>Interesting. Would it not work on either end of the lathe? I can see how using it to retract the dill bit would be very useful. Makes me wonder how the tapered adaptor thingie I got got might not out so well. Haven't tried it yet.