Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Rare Exotic & Domestic Hardwoods, Milled In-House in Oregon. Browse Unique Stock.

A little OT, Cutting Aluminum Gutter

Posts

A little OT, Cutting Aluminum Gutter

#1

A little OT, Cutting Aluminum Gutter

Craig Daymon

>I decided to better protect my sprinkler pipes from flying debris. I'm wrapping them in pipe insulation and, near the lathe, I'm going to cut a section of aluminum gutter to additionally shield it.

Anyone have advice on the best way to cut it? Tin snips seem to leave a very jagged edge (at least when used by me). A hack saw with backing?

Thanks in advance,

Craig

Re: A little OT, Cutting Aluminum Gutter

#2

Re: A little OT, Cutting Aluminum Gutter

Allen Neighbors

>Craig, if you know someone who works with metal building construction, they might just loan you a pair of nibblers. A Nibbler tool cuts little 3/8" long quarter-moons out of a piece of sheet metal as you push it along your line. If you were in the Childress area, I would loan you a set.

There is also a tool (short, scissor-lookiing thing) that will cut out a 1/8" wide "curly-cue" as you push it along your line. I've always just called them sheet metal cutters.

Both of these electric tools make working with metal a lot easier.

Re: A little OT, Cutting Aluminum Gutter

#3

Re: A little OT, Cutting Aluminum Gutter

Brian Hahn in SW Wisconsin

>I'd use my compound miter saw. My table saw would be my second choice. Carbide tipped saw blades cut aluminum with ease and don't distort the piece as much as snips. Follow that with a quick touch up of the cut edges with a file and you're done.

Re: A little OT, Cutting Aluminum Gutter

#4

Cutting Aluminum Gutter

Robert W - aka nailshooter

>When remodeling and changing room sizes we often cut gutter and cannot have a ragged or distorted edge. We drill a hole on the waste side of the gutter to insert a blade, and cut it with a fine tooth blade in a varible speed jig saw. With masking tape on the bottom of the table (we don't use the skid plate on the Bosch) it doesn't scuff or mark material.

Robert

Re: A little OT, Cutting Aluminum Gutter

#5

Re: A little OT, Cutting Aluminum Gutter

keith zimmerman, Normal, IL

>I've always just used airline snips. Believe me, the more you cut with them, the cleaner your cut becomes. I did my entire house with new aluminum gutters. By the time I was done, I could cut a clean, straight line with airline snips.

keithz

Re: A little OT, Cutting Aluminum Gutter

#6

Re: A little OT, Cutting Aluminum Gutter

JohnKJordan in East TN

>I just put up aluminum guttering on my barn. I used a battery powered circular saw with a carbide blade. This saw didn't have a big enough blade to go all the way through with one pass so a bigger saw would be better. It worked very well and left a straight and non-ragged edge. (I've used tin snips before.)

A saw will throw a lot of sharp metal so don't forget the safety glasses, or better, face shield.

JKJ

Re: A little OT, Cutting Aluminum Gutter

#7

Put the blade on with teeth facing the wrong

Garrett in Victoria

>way if you use a circular saw. It will cut more smoothly with much less tendency to grab.

Cheers. Garrett

Re: A little OT, Cutting Aluminum Gutter

#8

Re: A little OT, Cutting Aluminum Gutter

eaglesc

>If you are concerned about the rough edges get a apir of seamers.

Notch the ends at the corners and fold back to a hem.

This is what we do for galvanized duct work with raw edges.

You may have to make relief cuts if the metal has a curved profile.

That being siad.

In all the buildings I have put duct into I have never seen a sprinkler system with PVC piping.

If the system were done in black iron covering would not be necessary.

If appearance is a concern it is easier to sleeve the black iron with PVC pipe.