Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Super Resolution Thermal Imaging Camera

Conover Larthe Bearing assistance requested.

Posts

Conover Larthe Bearing assistance requested.

#1

Conover Larthe Bearing assistance requested.

B T Ferraro

>I've noticed a bearing noise. Perhaps best described as a squeak at 3/4 maximun RPM. The lathe has been relatively lightly used. I tried adjusting the preload a couple of times and it seemed to be gone. Now it's back. I started removing the spindle but the seal didn't pop out with light persuasion. Before going any further I would like to have another set of seals and bearings on hand before proceeding further. I've been unable to locate numbers despite numerous searches.

If anyone has access to this information it would be most appreciated.

ALso the manual stated that the front bearing need not be removed from the spindle but it seems to me to be difficult to imagine forcing grease into them while on the spindle. Would also appreciate suggestion for the removal of the bearings from the spindle should they need to be replaced as well.

Thanks for any assistance you might be able to provide.

Re: Conover Larthe Bearing assistance requested.

#2

Re: Conover Larthe Bearing assistance requested.

Brian Hahn in SW Wisconsin

>The rear seal is a pry out with a screw driver fit. Pry it out uniformly around the edge and it will come out. You will leave some marks on the metal, but that doesn't matter because the real seal is the rubber seal behind it. The spindle slides out from the rear with both bearings, so it isn't necessary to remove the front seal. Clean the bearings and races with solvent, then grease the bearings with no more than 1 tablespoon of grease (auto chassis grease is fine).

According to the manual, the bearings should be cleaned and greased at least every 2 years, even if the lathe is sitting idle. I only do it every couple of years. If you've never cleaned and greased the bearings, then they are way overdue.

Re: Conover Larthe Bearing assistance requested.

#3

Re: Conover Larthe Bearing assistance requested.

B T Ferraro

>Brian,

Thanks very much for the directions. I hadn't done a cleaning and relube because the manual led me to believe that so long as the belt was in good shape I was OK.. I should have taken into account the age of the lubricant though. I hope to get some time today to get to the cleaning.

Thanks again.

Re: Conover Larthe Bearing assistance requested.

#4

Re: Conover Larthe Bearing assistance requested.

Jake (SoMN)

>I replaced the bearings in a Conover I used to have, and had spare seals and all the bearing data....unfortunately when I sold it, it all went with.

If you take it all apart the bearing numbers are stamped on the outside of each bearing. Most bearing supply houses have cross reference tables and can help you out. If I remember correctly, the seals are different on each end, and it is nearly impossible to remove them without damaging them. The numbers are also on the ourside face of the seal. If you can get the numbers before you bend them up removing them it is easier.

Lastly, don't forget the handwheel nut is left hand thread.

Replacing the bearing is a pretty simple job. The parts were around 50 bucks, and I ordered extra seals.

Good luck.

Jake

Re: Conover Larthe Bearing assistance requested.

#5

Re: Conover Larthe Bearing assistance requested.

B T Ferraro

>Jake,

Thanks.

It does look like I'm going to need the seal on hand before going further. I'm finding gentle persuasion isn't working all that well. I didn't get the old ones out yet but did find the second part number on the the other seal. One was clearly marked the other stamped on. I'm going to get the new seals first. Then see if cleaning and lubing are all that's needed. After that I'll get a spare set of seals and bearings then I be ready if it's ever necessary again.

Do really appreciate the help.