Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

This is the most versatile work station you will ever use

What Parting Tool

Posts

What Parting Tool

#1

What Parting Tool

bhenr99

>Being new at this I see so many different parting tools in catalogs. What thickness is best and what brand would be best. The biggest think that I would be doing is 10" peppermill @ 2 1/2" dia. and some bottle stops. Thanks for any help.

Bob

Re: What Parting Tool

#2

Re: What Parting Tool

Donna Banfield

>Hi Bob

For your pepper mills, you would want a very thin parting tool, 1/16th. I use the Crown 1/16th, but there are several manufacturers that make that size. The reason you'd want it very thin, is assuming that you'd want the wood grains to line up when the mill is put together, a thinner kerf won't take as much wood as a thicker parting tool. The disadvantage to a thinner parting tool is the depth that you can effectively reach -- the thinner the blade/metal, the more likely it will flex.

On bottlestoppers, I suppose that you could use the thin parting tool to clean up the bottom or face of the stopper blank, where the wood meets the stopper (silicone, cork or metal), but if there was any wood surface showing, you could also use a skew or detail gouge, with better results.

If you become addicted like the majority of us have, you will quickly become a tool junkie ;^).

Re: What Parting Tool

#3

George Balock

Re: What Parting Tool

George Balock

>Bob,

I have three prting tools and use them fo differnt purposes. i use a thin Chriss Stott for boxes and peppermills. i use my 1/4 inch wide no name for general stuff and I use the no name 1/8" for squaring up places where I need an absolutely square joint. i hope this helps.

George

Re: What Parting Tool

#4

Try Penn State Industries *LINK*

Craig Daymon

>For a 1/16" parting tool, I know a several professional turners who have made them from old planer knives and such. Personally, I don't think there is any reason to spend much money on one.

Penn State Industries sells one for $9.95 with a handle. For some reason they call it a tenoning tool. I have one and it does the job just fine. I also have a diamond parting tool, which is nice because it has less chance of binding in the cut, but I reach for the 1/16" tool mostly. I put the link below.

-Craig


Penn State 1/16" parting tool

Re: What Parting Tool

#5

Re: What Parting Tool

Philip Duffy

>My favorites are; the old Sears tool that I cannot find a replacement for in any store, and the thin ones I make using a 6in. sawzall blade with the teeth ground down, and shortened to get a bit more stiffness. Grind a tang, make a handle, some epoxy and away you go! That is my first choice parting tool on all narrow applications.

Re: What Parting Tool

#6

Re: What Parting Tool

eaglesc

>I use a parting tool to cut my patterened pen blanks in half after I have chucked them into my Beall collet chuck.

The one I like the best?

An old table knife that I ground and honed.

Why buy it when I can make it?

Re: What Parting Tool

#7

Re: What Parting Tool

Allen Neighbors

>I've got an old Sears parting tool that I've used and sharpened so much that it's blade is about 1-1/2" long.

But my favorite is an Old Hickory butcher knife that I ground down... like the eagle guy... it's fun to make your own. :) It's about 1/16" thick, and makes a really nice tool.

Re: What Parting Tool

#8

Re: What Parting Tool

eliot d

>My favorite is one that I have no name for. It has a sliding blade whose length can be adjusted by loosening and tightening a set screw. I saw Mark Gardner with one when he was demonstrating at our club(CAW) in virginia. Only , as far as I'm concerned , he uses it upside- down -- larger cross section at the bottom; I prefer the larger part of the cross section at the top.