Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Personalized Wooden Watches, Engraved Free

Sorby Revolving Steb Centre -(for spindle turners)

Posts

Sorby Revolving Steb Centre -(for spindle turners)

#1

JL

Sorby Revolving Steb Centre -(for spindle turners)

JL

>I finally picked up one of these with a 7/8" diameter tooth pattern and a #2 MT. They do make a difference. I've had a Sorby Steb Centre for my headstock side for a while and really liked it.

The live centre for the tailstock allows me to have a minimal longitudinal pressure along the axis of the spindle. This means less flex and chatter when turning the longer, thinner spindles (I hate having to use a steady rest). If you aren't turning spindles, I don't know how much use it would be.

Re: Sorby Revolving Steb Centre -(for spindle turners)

#2

Re: Sorby Revolving Steb Centre -(for spindle turn

john lucas

>JL the problem I have with the stebcenters is the spring in the center point. It applies so much pressure I get chatter from that. I use a standard live center in my tailstock. I quit using my stebcenter and went back to a 3/8" spur drive. I can tighten it up quite tight for roughing and then when I get the spindle thin I back off the tailstock until it squeals and then tighten it a tiny bit. This gives me the least amount of pressure needed to drive the spindle.

Re: Sorby Revolving Steb Centre -(for spindle turners)

#3

JL

Re: Sorby Revolving Steb Centre -(for spindle turn

JL

>Were you turning your small, thin stuff? I'm turning kiln dried maple and oak. I think the thinnest that I go is maybe 1/2" with a total length of maybe 25-30". I haven't noticed any chatter (yet).

Re: Sorby Revolving Steb Centre -(for spindle turners)

#4

Re: Sorby Revolving Steb Centre -(for spindle turn

john lucas

>JL These are usually my mirror handles which are 10" long and vary from 3/8" to 3/4" along the length. I support the spindle with my fingers and that reduces the chatter considerably but I get quite a bit less when I back off the tailstock pressure

Re: Sorby Revolving Steb Centre -(for spindle turners)

#5

I gotta agree with John

Brian Hahn in SW Wisconsin

>I tried the Steb Centre for a while. It slipped while roughing, cutting a nice circle in the end of the piece, then the spring pressure was too heavy for the delicate thin turning. Like John, I now use a small spur drive and a point in the live center.

Re: Sorby Revolving Steb Centre -(for spindle turners)

#6

JL

Re: That must be it then..

JL

>The arm posts and stiles are 1/2" at the smallest diameter and the stretchers are 5/8" at the end. I've got Steb centres at both ends now and the chatter is nearly non existant. I've got the teeth of the centres just engaging in the wood.

Re: Sorby Revolving Steb Centre -(for spindle turners)

#7

steb on thin spindles

JohnKJordan in East TN

>>...the problem I have with the stebcenters

>is the spring in the center point

I use the 1//2" steb center on all of my thin spindles and it works very well for me. The spring is indeed strong and will exert a lot of force, often enough to crack thin blanks especially of hard, brittle woods.

However, the method I use eliminates the problem. Before mounting, I use a hand gimlet to make a small hole centered in each end of the blank. This only takes about 5 seconds. The point is seated in the hole and the pressure is reduced, and has the further advantage of quicker mounting at the desired point.

Note that the spring can be removed and modified if desired for less pressure.

JKJ

Re: Sorby Revolving Steb Centre -(for spindle turners)

#8

Re: steb on thin spindles

john lucas

>I've thought about modifying the spring I just haven't done that yet. I like the teeth idea I just don't like the center spring point.

Re: Sorby Revolving Steb Centre -(for spindle turners)

#9

Keith Tompkins

Re: Sorby Revolving Steb Centre -(for spindle turn

keith tompkins

>A neat trick for long, thin spindles, such as finials. I form a tenon on my stock, and glue it into a hole drilled in a waste block, held in a chuck. Minimal pressure is needed from the tailstock, and the piece never slips, while whip is reduced significantly.

Re: Sorby Revolving Steb Centre -(for spindle turners)

#10

Re: Sorby Revolving Steb Centre -(for spindle turn

Russ Fairfield

>Make a block as Keith describes, but cut a slit in one side so it will clamp down on the tenon as you tighted the chuck. Works the same, but the waste block can be reused.

Re: Sorby Revolving Steb Centre -(for spindle turners)

#11

Re: Sorby Revolving Steb Centre -(for spindle turn *LINK*

charlie belden

>Totally agree about the spring tension in the Stebb Center tail stock drive being way too high when it comes to fine spindle turning.

If you have a set of "pin jaws" and a scroll chuck I'm not sure why don't chuck the blank directly in the chuck jaws since they'll close down to a little under 1/2" diameter.

For longer thin spindles I just chuck up a square blank and support the other end with a live center - the one with a small pin and a ring. The small pin doesn't penetrate as deep as the longer, larger pin on the regular tail center and it's mainly the ring that holds the end of the blank - without splitting anything.

Once I've got the last inch or two pretty much done I point off the end from the tail center, remove the tailstock and turn the rest just held in the chuck jaws.

Once you've got things roughed round - and IF you use semi sharp tools - AND don't try hogging off a lot of wood in one pass - wobble and flexing aren't an issue.

Third photo on the page at the attached link shows what can fairly easily be done - in this case out of Santos mahogany, which, with its open grain is a little trickier to turn than say maple.

And if you want to turn REALLY thin stuff, as in 0.02" diameter, check out the third from the bottom photo on the next page - in poplar - done with on old bayonet saw blade - with a paper towel handle.


thin spindle turning using just a chuck

Re: Sorby Revolving Steb Centre -(for spindle turners)

#12

Chucks for spindle turning

Ron in Drums PA

>That's the way I turn finials.

I know I posted this picture before, but take notice that I'm using a set of pin jaws to hold the stock. The longest finial I turned this way was 6"-7" in length.

The trick is to start and finish the tip then work your way back to the chuck.

For reference the skew is 1/4" round.


img

Re: Sorby Revolving Steb Centre -(for spindle turners)

#13

Re: Sorby Revolving Steb Centre -(for spindle turn

russ Fairfield

>Charlie,

Having the piece of wood acting as a "false jaw" keeps the tool from coming off the end of the wood into close proximity with a piece of steel that is spinning in excess of 2500 RPM. It didn't take very many contacts between tool and chuck to convince me that this might be a better way to hold a spindle by its tenon.

Re: Sorby Revolving Steb Centre -(for spindle turners)

#14

Re: Sorby Revolving Steb Centre -(for spindle turn

JohnKJordan in East TN

>>A neat trick for long, thin spindles, such as finials.

>I form a tenon on my stock, and glue it into a hole

>drilled in a waste block, held in a chuck.

Another way with the same advantage is to turn a short morse taper on the end of the wood and press it into the headstock spindle as a jam chuck. Besides being very quick (once you learn to cut the taper!) it is low profile (no chuck to catch fingers) and minimum length. The latter was especially important when I set up on site and turn wands on a mini lathe - the lathe is just too short to hold the length I need any other way.

JKJ

Re: Sorby Revolving Steb Centre -(for spindle turners)

#15

Re: Sorby Revolving Steb Centre -(for spindle turn

charlie belden

>RON wrote:

>Charlie,

>Having the piece of wood acting as a "false

>jaw" keeps the tool from coming off the end

>of the wood into close proximity with a piece >of steel that is spinning in excess of 2500

>RPM. It didn't take very many contacts

>between tool and chuck to convince me that

>this might be a better way to hold a spindle

>by its tenon.

Two ways to avoid that potential problem

1. Start with a long blank in the pin jaws

of the chuck turning from the "top" of

the finial back towards the base. Turn the

tenon last. At that point it's parting tool

work which doesn't require much space

and doesn't involve rolling the tool.

2. Turn the tenon first and the details of the

bottom of the finial, turn the blank

around and chuck up the tenon then turn

the rest of the finial.

charile b