Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Super Resolution Thermal Imaging Camera

Sprinkler pipes are not fly wood proof!

Posts

Sprinkler pipes are not fly wood proof!

#1

Sprinkler pipes are not fly wood proof!

Craig Daymon

>I was roughing a piece of Purpleheart last night and a corner came off and went right for the plastic sprinkler pipe. Instant shower! I really wish the pressure in my regular shower was anywhere near that. Finally found the shut-off valve while on the phone with 911. Unfortunately, that pointed out the fact that there is a slow leak back by the shut-off. Fire marshall stopped by today and told me that all the sprinkler heads on the 2nd floor (no, not the basement) are recalls and need to be replaced. Spent the day mopping up wet sawdust and cleaning tools, talking to sprinkler contractors and fire marshalls.

As I understand it, in an unfinished basement (like a workshop does not constitute a finished basement...so much for taste) these pipes should be copper. Well, they are not. So I also need to figure a way to shield these pipes from any future projectiles.

Still haven't turned the lathe back on...or the grinder...or the mini-lathe that was behind the 3520. Fingers are crossed.

Hope everyone else is having a better day.

-Craig

Re: Sprinkler pipes are not fly wood proof!

#2

Steve Kubien

Re: Sprinkler pipes are not fly wood proof!

Steve Kubien

>Hope nothing was seriously damaged. Here in the Great White North I have never heard of any sort of plastic being used as a water supply pipe except very low pressure stuff for ice makers in fridge/freezers. Copper (type M I think) is the standard in these parts, no matter where in the house it lies. There is a product called Kytec (sp) which is a plastic inner wall, surrounded by a thin copper tube (less than a millimetre thick) surrounded by another plastic tube. It helps to insulate so hot water doesn't lose as much heat as it travels. It is great for guys like me who don't solder. I doubt you could pierce it with a flying brick.

Take care,

Steve Kubien

Re: Sprinkler pipes are not fly wood proof!

#3

What if ????

Dennis Yoder

>What would have happened it that pipe was carring compressed air at 120-140 psi and what was hurled were scarry sharp plastic shards????

Pucker factor 9!!!!! Dennis Y

Re: Sprinkler pipes are not fly wood proof!

#4

plastic pipe for compressed air *LINK*

JohnKJordan in East TN

>I heard (in a safety meeting once upon a time) that although it is often used, plastic pipe is hazardous and prohibited for compressed air. The hazards are the same as for pressure vessels, discussed earlier in the air compressor tank thread here. (Pipes/vessels filled entirely with liquid do not present the same hazard.)

I found this:

...sections 842.32, 842.43 and 849.52(b) of the American National Standards Institute/American Society of Mechanical Engineers (ANSI/ASME) B31.8-1986, Gas Transmission and Distribution Piping Systems Standard, limit the operating pressure of plastic piping distribution systems to 100 pounds per inch (psi) and prohibit the installation of such systems above ground except where ". . . the above ground portion of the plastic service line is completely enclosed in a conduit or casing of sufficient strength to provide protection from external damage and deterioration."


OSHA bulletin

Re: Sprinkler pipes are not fly wood proof!

#5

Re: What if ????

Craig Daymon

>The sprinkler guy and the fire marshall had a discussion about gas pressure and the piping. The sprinkler guy was telling about a builder that wanted him to use compressed air to test the pipes when the weather was too cold to run water, which got him into explaining the hazards of such a method and why they had to wait for a warmer day.

Fire marshall also told a story about an older metal worker who was milling a very long (10+ feet) piece of steel when the back end began to whip and he grabbed for it instead of shutting off the machine. He didn't survive.

The lathe still runs (for now). Haven't checked the mini-lathe or the grinder just yet. The grinder is pretty well sealed, so I'm hoping it's fine. The mini picked up some rust, so that needs a cleaning before it goes back into use. That cast iron rusts quick!

Anybody have to protect similar piping? I still need to get some flashing or something up to guard against this happening again.

-Craig

-Craig

Re: Sprinkler pipes are not fly wood proof!

#6

Hmm? A couple of questions?

Barry Irby

>I thought some sprinkler systems were "dry pipe", meaning they were filled with air until a fire triggered a head and then the air exhausted until water made it there and put out the fire. This was to prevent freezing. (Freezing would burst the pipes and the water could do about as much damage as a fire.) If this is true, are these systems dangerous?

And, Locally, in new construction, I think every supply pipe system is put under about a hundred psi of air and left for 24 hours to see if it holds. Many of the pipes are CPVC. Some are PEX. Other trades are often working in the house while the pipe is under pressure. Does that mean these pipes are dangerous during the test?

Re: Sprinkler pipes are not fly wood proof!

#7

Re: Hmm? A couple of questions?

John Veerkamp

>Typical house water systems run 40-60psi. In fact most water using appliances require a pressure reducing valve if the pressure is higher than that. That said, pvc , cpvc, pex pressure pipe are all rated at 200psi so the 100 psi for testing is not dangerous to others in the area. Leaking joints are not a danger for shrapnel but can be quite disconcerting when the begin to whistle.

John