Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

If you sell to woodworkers, your customers are already here

Basic Tool Set and Skew Question

Posts

Basic Tool Set and Skew Question

#1

Basic Tool Set and Skew Question

Rob Hix - King George, VA

>Hey all,

I am getting ready to start some turning. I have turned before and am not nearly a professional, but I am fairly proficient with all the tools. Currently I have a 1" skew (not oval), 1/4" parting tool, 1/2" round nose scraper, 3/8" spindle gouge, and a 3/4" spindle gouge. What else do I need? For right now I will be sticking with spindle sanding. I want to make stools, chairs, candlesticks, etc. I will probably delve into bowls next spring.

Also, I am thinking that I want a smaller skew. I am thinking a 1/2" for some of the smaller work that I am wanting to do pretty soon. Which is better, the oval shaped skew or the rectangular shape? Just need your opinions on this.

Thanks for the help. I can't wait to get back into this.

Rob Hix

Re: Basic Tool Set and Skew Question

#2

Re: Basic Tool Set and Skew Question

JohnKJordan in East TN

>Sounds like you have a pretty good set of tools. Above all, a good sharpening system is a must.

I like a narrow parting off tool, 1/16". For smaller spindles I prefer a 1/2" skew. (I like the flat skews instead of oval since I find them easier to sharpen, but I can't guess as to which is "better".) A roughing gouge is helpful. A smaller detail gouge is nice if the shaft is not too long. Some people love the triangular point tools for cutting beads.

Something else I found adds to my turning fun: more than one of each size of tool. This lets me go twice as long between sharpenings.

JKJ

Re: Basic Tool Set and Skew Question

#3

Re: Basic Tool Set and Skew Question

john lucas

>I would also suggest a rough out gouge for roughing out spindles. I like a 3/8" spindle gouge and if your going to do bowls I would suggest a bowl gouge. I like 3/8 or 1/2". I have an oval skew but flat skews are probably easier to sharpen. I use a 1" skew for all but the smallest turings. Then I use a 1/4" round skew.

Re: Basic Tool Set and Skew Question

#4

Re: Basic Tool Set and Skew Question

Ron in Drums PA

>I have both, flat and oval... Oh and a round one too. I use the flat ones with the edges rounded over mostly. I think the ovals are fine, mine is 1-1/4" and I don't often need one that big.

The round one I have is a 1/4" skew, really nice.

Re: Basic Tool Set and Skew Question

#5

Re: Basic Tool Set and Skew Question

keith zimmerman, Normal IL

>I have 1/4", 1/2", and 3/4" skews. I use the 1/2" most of the time. it is a traditional skew. I also hone with the diamond card several times between sharpenings.

keithz

Re: Basic Tool Set and Skew Question

#6

Re: Basic Tool Set and Skew Question *LINK*

Darrell Feltmate

>For spindle turning I like a 1" roughing gouge, 1" skew, 1" straight chisel, 3/4" skew I ground from a parting tool, 1/4" round skew I made from a round tool bit, and occasionally a 3/8" spindle gouge. A thin bladed parting tool is nice too as is a 3/8" three sided point tool I made from a tool bit. Also, make or buy a sharpening system. It saves a lot of aggravation and speeds the learning curve tremendously. There is one to make on my site and commercially I like the Wolverine, but there are a lot of good ones out there.


Around the Woods: Sharpening