Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

THE WOODRAT IS BACK!

Drilling a long, thick, accurate hole...

Posts

Drilling a long, thick, accurate hole...

#1

Steven Antonucci

Drilling a long, thick, accurate hole...

steve antonucci

>I'm in the process of making a very large boring bar. It's 3/4" x3' long, and I would like to bury about 12" in the handle. I need to be able to do one of the following things:

1.) drill a long hole without the bit wandering

2.) rout a 3/4" semi circle on two pieces of wood

3.) not use wood for a handle- I was thinking blackpipe wrapped with duct tape and a set screw...

Before I go the blackpipe route, anyone have a secret recipe for long accurate holes?

Steven

P.S. The bar is in an oak handle now and it probably wandered by 3/8" along 8" of depth.

Re: Drilling a long, thick, accurate hole...

#2

Re: Drilling a long, thick, accurate hole...

jeff myroup

>as for the drilling I don't know, But I am in the process of doing the same. I am going with pipe so I can fill the rest not taken up by the bar with lead shot. I am also going to tie the length of pipe with half hitch knots tied out of small nylon line for grip. I was then going to buy some of that plastic kote that you can dip tools in, to coat the handle.

jeff

Re: Drilling a long, thick, accurate hole...

#3

Re: Drilling a long, thick, accurate hole...

Ed McDonnell

>If you want to use two (or more) different types of wood to create a really custom handle, the router approach (using a bullnose bit) would be very easy. If you don't want contrasting woods, then you're better off with a solid piece of wood, in my opinion, using the approach below.

You can address wander in the drill bit by using an oversize blank for the handle. Drill the hole and then mount it on a mandrel (3/4" piece of steel held in a chuck) when you turn it to shape. That will force the handle to be parallel to the drilled hole.

Ed

Re: Drilling a long, thick, accurate hole...

#4

Easiest way, IMO

Bill Howatt

>

Re: Drilling a long, thick, accurate hole...

#5

Re: Drilling a long, thick, accurate hole...

Brian Hahn in SW Wisconsin

>Spoon bits are the traditional drill bit used for deep straight holes. Lamp augers often are spoon bits. However I haven't seen either of them recently.

Using riven (split) wood so the grain runs straight along the handle will minimize the drift since most bits like to follow the grain on end drilling.

I've had only moderate luck with a hand auger bit, turning the bit with a brace while feeding into a rotating piece. I drilled out the centers of two hickory handle blanks about 20" long, drilling from each end. On one blank, the holes were connected but I couldn't see light, on the other one the holes were within 1/8" of dead on. Both blanks were the stems of small saplings and I was trying to drill out the pith.

Re: Drilling a long, thick, accurate hole...

#6

Re: Drilling a long, thick, accurate hole...

Chuck Engstrom

>Hi Steve -- I routinely drill 1/2" holes of 12 to 18 inches through end-grain of poplar. Wandering is always a problem, but my best results seem to come from starting with a Bullet drill bit mounted in a stout chuck on a stout lathe with the material turning at a relatively slow speed and modest feed rate for the drill bit. Once I've gone the full length of the Bullet bit, I have a couple of longer ones, just longer brad-point types, that I use to extend it as needed.

I am always able to drill all the way through my stock so I then have the option of mounting the workpiece centered on the hole at each end, which of course centers whatever form I turn thereafter. I use a shop-made brass insert in the hole which allows me to drive the piece with a Steb center.

I do a bunch of work for a fellow who drills holes of 7 feet and more straight through cedar for lampposts and such with almost no wandering. His setup uses a special auger held captive at several points along its length so that it has less tendency to flex and thus let the end wander. Quite a rig but not one you'd want to duplicate for a quick small job. His auger is much like the lamp augers available to turners, at 5/16 or 3/8, but they are pretty flexible and would probably work a lot better if they had the moving supports holding on to them like his setup.

Good luck with it!

Best--

CHuck

Re: Drilling a long, thick, accurate hole...

#7

Re: Drilling a long, thick, accurate hole... *LINK*

Craig Daymon

>I always heard that a gun drill with its single flute bit wouldn't wander. Based on that, I bought a set of long, single fluted bits, I think from Garrett Wade. I haven't put it to a test yet, so I can't say it will work. Maybe someone here can say whether this is a sound approach?

I plan to grind the lead screw to a point so they won't draw the bit into the wood, but let me push it in and still give me a point to align with my target.

Good luck,

Craig


Garrett Wade 18" long single flute bits

Re: Drilling a long, thick, accurate hole...

#8

Steven Antonucci

Thanks for the ideas

steve antonucci

>you can never have too many tools...

Steven

Re: Drilling a long, thick, accurate hole...

#9

Re: Drilling a long, thick, accurate hole...

john lucas

>Steve I've played with long hole boring and it's tough. The best methods I found were Lamp Augers, and predrilling the hole. If you use a lamp auger it needs to be really sharp. Much sharper than it comes from the factory. Feed it slowly so it does the work and clear the chips really often. Bore half the hole from one end and then turn it around and drill the other half.

I've had some success drilling holes in both ends of the piece on the drill press and then connecting them with a longer bit in a hand drill.

The best information I found was doing a google search on wooden flutes. There is an excellent article on making your own bits. I've only drilled 3/8" holes and the wooden flutes need 3/4 to 1" holes and he describes the tools he makes to get there. Sorry I don't have time to look it up but I still have a tone of things to do before bedtime. I'll try to look it up in the morning if you haven't found it.

Re: Drilling a long, thick, accurate hole...

#10

Boring Bar

Jorge Castaneda

>Steve,

making a long drill is easy, shape the bar like the picture and make the point of the bar off center to make it stay true, this is what we used in a recorder making course I took. Take away exactly to 1/2 the diameter and make it a couple inches long at least, so shavings have a place to go, back often to get rid of them.

I got very good results once I made my own steady, using a bearing pillow I had around, the bar has no handle and is held and pushed in with vise grips.

Jorge


img

Re: Drilling a long, thick, accurate hole...

#11

What I did........

Barry Irby

>I took a blank long enough to make the handle and ripped it in half lengthwise. Used a core box bit to cut a 3/4" trough down each piece on the ripped surface.

On the lathe, I turned a two inch long dowel 3/4" in diameter and then parted it in half.

Glued the two halves of the blank back together with the dowels in each end with the center marks pointed out. Put it back on the lathe using the center marks on the dowels and turned the handle. Cant remember whether I parted the ends off to reveal the hole or just drilled through the plugs.

Don't have a core box bit? Just cut a 3/4" square dado and glue a short block in each end and then drill through one or both. A round shaft will work fine in a square hole. Just center on the little plugs in the end and turn the handle.

Re: Drilling a long, thick, accurate hole...

#12

Other View

Jorge Castaneda

>Here you see the off center point.


img

Re: Drilling a long, thick, accurate hole...

#13

Steady

Jorge Castaneda

>Here you see the pillow block used to make the steady, notice the wood insert to the diameter of the recorder we were attempting to make.

Hope this give ideas...

Jorge


img

Re: Drilling a long, thick, accurate hole...

#14

Don't Drill. Cut & Rout.

Garrett in Victoria

>Drilling long holes with twist bits is not easy. Aside from drift, the bit will likely bind.

An easy alternative is to slice an oversize blank lengthwise, then use a bull-nose router bit of the necessary diameter to groove each piece, and glue the blank together again.

Cheers, Garrett

Re: Drilling a long, thick, accurate hole...

#15

Re: Drilling a long, thick, accurate hole...

Danny Wells

>Actually a gun drill looks kind of like a shallow fluted gouge with one cutting edge on the end, and it is designed with either air or a liquid as a fluid that ejects the chips from the bottom of the hole. The drill has a channel through the length of the bit for the air with an exit hole at the bit end.

The hole can be drilled at a moderate speed all in one stroke, because the chips are being ejected continuously. I don't understand the physics, but the drill stays relatively centered all the way from end to end when drilling homogenous material.

Gun drills are what bag pipe makers, flute makers and of course rifle barrel makers use to drill long holes. There are a lot of other uses as well.

They are rather expensive (around $100 and up), so you probably don't want to use this method for one handle.