Looking for book on Hollow Forms
Ben Ragusa, S. Jersey
>I have looked for, but not found any instructional books on hollow forms. I would prefer a book over a video, but could be persuaded by your recomendations. What's your favorite one?
Knowledge You Can Build On — Est. 1998
Looking for book on Hollow Forms
Ben Ragusa, S. Jersey
>I have looked for, but not found any instructional books on hollow forms. I would prefer a book over a video, but could be persuaded by your recomendations. What's your favorite one?
Re: Looking for book on Hollow Forms
James McClure
>The May/June 1979 issue of Fine Woodworking has David Ellsworth's article on hollow form turning. Not a bad place to start if you can find the back issue.
Re: Looking for book on Hollow Forms
john lucas
>Ben I think it's hard to beat the John Jordan videos. They are straight forward without getting too fancy. His video on the wood movement is also excellent. I haven't actually seen any books on just hollowing. They are probably out there I just haven't seen them.
Don't know any books either
steve antonucci
>I have about 50 books or so, and the best books for hollow turning might devote a chapter or two. What are you trying to "learn" from the book?
Steve
(I'm in Northwestern NJ...and there are others scattered throughout the state...)
Re: Looking for book on Hollow Forms *LINK*
Larry Bisbee
>There are several DVD�s that I like. One is the �Hollow Forms and Lidded Urns with Mike Mahoney� and a couple of DVD�s by Trent Bosch; �Sculpting Wood � Beyond the Lathe� and �Vessels of Illusion�.
http://www.craftusa.com/
Re: Looking for book on Hollow Forms
Charles Watson
>I haven't seen any good books on the subject, but John Jordan's video is the best one that I've watched.
Ben, I agree with John
Ruth Niles
>There really aren't any books for basic hollow forms. The ones that are available are quite advanced or with carving or enhancements. John Jordan's DVD on hollowing is an older one but probably the best for basics. His newest DVD is great for the "getting the maximum from your wood with a minimum of problems" (to quote from the jacket!).
Woodturning: A Fresh Approach
Brad Vietje
>Ben,
I like John Jordan's video a lot, but as far as books go, I think the best by a LONG shot is Robert Chapman's Woodturning: A Fresh Approach. Its a very good book in general, but it does have some very good sections on hollow forms. My favorite turning book.
Safe spinning,
Brad Vietje
Newbury, VT
Re: Thanks, Brad.
Allen Neighbors
>
Re: Looking for book on Hollow Forms
russ Fairfield
>It sounds like somebody needs to make a video on Hollow Forms.
Hint, Hint...Bill Grumbine
Chip in Plano
>Sounds like the third in Bill's series.
For real, check out the Packard Woodworking and Craft Supplies websites. One or both have a decent selection of turning videos. The very nature of HF makes filming them a challenge. I know I have a hard enough time craning my head over with a flashlight to get a good peek inside.
Re: Looking for book on Hollow Forms
eliot d
>I'm sure you know that Jordon and Ellsworth have done it, and I'm sure there are others. I guess you mean someone else from this site. According to Jimmy Clewes, his videos ( "Turn it On", for example) cost about $20,000 to produce. (He also claims to have gotten his money back in a week.)
Re: Looking for book on Hollow Forms
gary s clarke
>A book by Robert Chapman has about 30 to 40 pages on beginning hollow form turning. I haven't turned enough hollow forms to say if it would be current. It was published in 1999. The title is Woodturning--A Fresh Approach. ISBN--1861081197. Why do I have this book? Because I am a book junkie.
that's an excellent book - highly recommended
GaryG in MD
>