Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Super Resolution Thermal Imaging Camera

what's the best way...?

Posts

what's the best way...?

#1

what's the best way...?

GaryG in MD

>I'd like to make a disk sander for my lathe. I figure a faceplate on a plywood circle ought to do it. Except I can't think of the "best" way to attach the sandpaper. I'm planning for a 9" diameter. The big sheets of sandpaper don't normally come backed for Velcro. Double sided tape would be uneven. I can't just glue it on because it has to be changed all the time. Has anybody done this and come up with an easy, quick, cheap, simple, practical solution? TIA, Gary

Re: what's the best way...?

#2

PSA sanding disks

Brian Hahn in SW Wisconsin

>PSA (sticky back) sanding disks are readily available in the 9" size in a variety of grits. These are the same disks used on stationary disk sanding machines. That's what I would use.

Re: what's the best way...?

#3

Re: what's the best way...?

Mike Jones

>In the store that sells automotive finishes, they sell a disk adhesive made for exactly that use. I haven't been able to find the adhesive in aerosol, but the stuff in squeeze tubes works great.

Best that you seal the plywood good, or you'll have trouble changing disks.

Re: what's the best way...?

#4

Thanks,Brian,...

GaryG in MD

>...I'll check it out. Sounds good. ...Gary

Re: what's the best way...?

#5

Thanks Mike, ...

GaryG in MD

>...yeah, it's too bad it's not a spray. Good to know. ...Gary

Re: what's the best way...?

#6

Re: what's the best way...?

Cyril Griesbach

>3M makes a spray adhesive but I'd just go with PSA discs as already mentioned. Just be sure to make your disc of Melamine (sp?) covered MDF so it will be easy to change abrasives discs. When removing one disc to replace with another grit, put the removed disc on wax paper so you can reapply it again later.

Re: what's the best way...?

#7

Dick Hines

Re: what's the best way...?

Dick Hines

>Make your sanding disk out of MDF board and the sticky back sanding disk will stick to it.

Re: what's the best way...?

#8

Re: what's the best way...?

john lucas

>Gary The PSA discs are hard to beat. 3M sells several sprays that work but they are a more heat sensitive than the PSA discs. You can get a can at the box stores. I believe it's called Super 77. They have several so make sure this isn't the positionable adhesive that I think is Super 75.

Re: what's the best way...?

#9

Steven Antonucci

a few ways...

steve antonucci

>If I wanted to do it cheaply, I'd have to assume that the standard sandpaper is cheaper than PSA disks, and a can of Super 77 or Super 90 lasts a long time. Instead of trying to change the paper, I'd make multiple disks of "fixed grit", and I'd have a small glue block on the back to grip with a chuck. Loosen the chuck, change disks, move on to the next grit. When the grit was worn out, either change the PSA disk or sand paper and go.

And of course, I'd probably "double up" on the MDF/Plywood, just because I'd want the additional stiffness. I have enough MDF scrap laying around to do this with no additional costs. Did I mention cheap?

Steven

Re: what's the best way...?

#10

Regular sandpaper vs resin bonded

Brian Hahn in SW Wisconsin

>Regular sandpaper is indeed cheaper, but resin bonded (or is it resin on resin) is designed for high speed power sanding and it lasts many times longer.

Multiple disks, each dedicated to a single grit is a good idea.

Re: what's the best way...?

#11

Steven Antonucci

Agreed, but by regular I meant...

steve antonucci

>the stuff you tear and put on QS palmsanders. I like the Norton 3X when I can find it, but I don't know if it's resin bonded or other? My recommendation for the "on the cheap crowd" was to buy sheets and spray adhesive mount it vs. PSA.

You can run the lathe at the right speed to minimze heat problems. I've stood next to a 16" disk at 3000 rpm and it's scary as all heck... heat and wear being the least of the issues. It did do a phenomenal job at cleaning off all of the shavings on the ways, though...

Just to be extra safe, I'd probably run a few screws through the glue block into the MDF. just in case I ever make the 3000RPM mistake again... :-)

Steven

Re: what's the best way...?

#12

Re: Agreed, but by regular I meant...

Barry Irby

>Steve, My non-woodworking son walked in and was chatting. He pushed the "UP" button on my DVR lathe and cranked it up to 3500 RPM with a set of partially expanded Cole Jaws on a mini chuck. Then he turned it on. It made an enormous whirring noise and he turned it off. Stupid and lucky. If you are going to do stupid things you need to be lucky or you will get the Darwin Award.

Re: what's the best way...?

#13

Thanks all...

GaryG in MD

>These are all very good ideas. It has given me some new lines of thinking and several possible ways to go. That's what I wanted. Excellent. Thanks to all of you for your thoughtful replies. ...Gary

Re: what's the best way...?

#14

That's what I thought you meant...

Brian Hahn in SW Wisconsin

>The resin bonded sandpaper I meant was the cloth-backed stuff that they make belt sander belts out of. The grit is bonded with a top layer of resin that keeps it in place for power sanding. It is also the same type of paper used on the Power-Lock and Roto-Lock disks that Bill Neddow mentioned in the high speed sanding thread.

The Norton 3X and 3M Sandblaster papers are very good, but they aren't designed for use on a sanding disk. Anything more than just kissing the paper will knock the grit right off. Been there, done that.

Re: what's the best way...?

#15

Steven Antonucci

Ahh! I wonder...

steve antonucci

>if you could use spray adhesive to bond that stuff to a substrate over a 9" disk? Super 90 is a pretty good glue and I know that you can pull on those types of disks without them shredding...

I just might have to do this a little bit later today...

steven

Re: what's the best way...?

#16

Re: Ahh! I wonder...

Allen Neighbors

>Steve, I use 3M spray adhesive. I bond garnet 120 grit to a 9" aluminum disc on one of my belt sanders. Old hair dryer gets it hot enough to peel off when I have to replace the paper. Then I clean the old adhesive off with Lacquer thinner.

Re: what's the best way...?

#17

Re: what's the best way...?

Don Evans

>You can use PSA as stated, but generally they only come is very course grits cause of their purpose. But you can make your own using the special spray glues made for this purpose.

You can also buy a 10" steel disk made for table saws for this purpose. If going with plywood you might also find it works much better if you put neoprene on the ply, but only neoprene the really thin stuff. Packard sells round one's but the middle is cut out, these are used for vacuum chucking on lathe. $4.95 for 8" one.

I'd put it on with more permanent glue like contact cement, then use the PSA tempy type sprays for the sandpaper.

I'm not in shop so cannot look now but I think my tempy spray glue is called 77, even Lowe's carries it around here.

Don

Re: what's the best way...?

#18

Re: what's the best way...?

GaryG in MD

>Thanks Don. That's good info. I was thinking about maybe using a thin backing but not sure if it would hold up or if the discs would stick to it. More food for thought... ...Gary

Re: what's the best way...?

#19

Re: what's the best way...?

Dennis Yoder

>Woodworkers Supply has discs that have PSA on one side and Velcro on the other so you can use velcro backed paper. Sold usually for converting large discs on stationary grinders to be able to use velcro backed sanding discs. Dennis Y