Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Good Hope Hardwoods - Walnut Slabs & Specialty Hardwood Lumber

Robinair vacuum Pump

Posts

Robinair vacuum Pump

#1

Robinair vacuum Pump

Michael Stadulis, in Gloucester County, NJ

>Hello,

I have an opportunity to purchase a used Robinair 15101 B which repotedly pulls 5 CFM. I can't determine how many inches it pulls, but it is a 2 stage A/C refrigerant pump and I suspect it has good specs which I'll confirm. It is a 2 stage oil-filled vacuum pump as well and I understand that the oil creates better vacuum than an oil-less pump. Does anyone have one? Seems that everyone discusses the oil-less Gast pumps for turning. Are there advantages for each?

Mike

Re: Robinair vacuum Pump

#2

Re: Robinair vacuum Pump

George Van

>Hi Mike, I have one and you are right, they pull good volume. I had a 15-inch bowl on it two days ago that had a bug hole near the bottom and the bowl still held. When I finished the chuck was covered with sanding dust that was sucked in through the hole, a good reason for a filter in the line.

On the downside I am experiencing a vapor (smoke-like) mist coming from the exhaust after the pump runs a few minutes, the oil temperature gets to 220 degrees rather quickly. I have run a hose from the exhaust into the bottom of a pail of shavings hoping to filter this but that did not work, the air in the shop still gets cloudy within a half hour. I am told this is common with certain types of pumps and manufacturers can supply a Demister Filter to trap the oil without blocking of the airflow. Mark Mandell built one using bronze wool in a container. My next step will be to exhaust outside.

I am using a coiled air hose with quick disconnect to attach to the lathe, I am going to replace this with a barb and larger diameter hose to allow better air flow and possibly help this situation. I am not sure it will because vacuum at 28� is still a vacuum and I assume flow will pretty much stop.

Re: Robinair vacuum Pump

#3

Re: Robinair vacuum Pump

Tommy Holmes

>I have the same problems with mine. The oil and pump get very hot and I get an oil mist that fills the shop. I thought that I may have slightly over filled the reservoir and that there might be something wrong with my pump so I'm glad to hear that this is may be common in this pump. I had thought of a demisting filter but have just not got to doing anything about it.

Re: Robinair vacuum Pump

#4

Re: Robinair vacuum Pump

George Van

>I do not think it is a good thing to breathe the fumes from the pump as this is oil?

Re: Robinair vacuum Pump

#5

Re: Robinair vacuum Pump

Tommy Holmes

>I agree, it can't be good for you. I use it very seldom because of it and try to use it at short spurts so it doesn't become a problem.

Re: Robinair vacuum Pump

#6

Re: Robinair vacuum Pump

Bill Howatt

>It is very definitely not a good thing to breath oil mist fumes.

Bill

Re: Robinair vacuum Pump

#7

Re: Robinair vacuum Pump

Mark Mandell - Gone Round In Jersey

>George & Tommy,

The Robinairs are, I'm told, designed for A/C techs working on condensers that are outside so that the misting is not a problem. With the pump inside, you have two choices; a condensing filter or piping the exhaust outside. There are "demister" units available (some will run you into $$), but a spin filter such as is used on compressed air systems will go a long way toward solving your problem. It'll make your pump quieter as well. I had some left-over 1/4" copper tubing so I formed up a 6x6" condensing coil with the outlet buried in a 2" copper cup stuffed with bronze wool. (steel wool would work just as well). The coil cools the flow from my pumps which then separates a lot of the mist and then the wool takes the next step. I didn't have a fog problem, but I could smell the oil after the vacuum had been running for a little while. Not any more, however.

Re: Robinair vacuum Pump

#8

Re: Robinair vacuum Pump

Tommy Holmes

>Thanks for the info Mark. That sounds like an easy enough fix. I'm going to try it and finally get use out of this vacuum pump like I'm suppose to be able to do.

Re: Robinair vacuum Pump

#9

Re: Robinair

Mark Mandell - Gone Round In Jersey

>Tommy,

FWIW, when my compressor-cum-pump outfit finally discombobulates, I plan on getting one of Bernie's rebuilt 5-6 cfm Robinairs.

Remember though, that on an oil-lubed pump you REEEEELLY need a good dust filter (that you clean often) between your lathe and the pump. If you get the thing gummed up with oil + 1 micron dust sludge, you'll be very sorry.

mm

Re: Robinair vacuum Pump

#10

An easy filter

Robert W - aka nailshooter

>A solution that I have seen was to pipe the exhaust into an upside down Gatorade bottle full of steel wool. The piping just went into the bottle about 1/2 inch. At the bottom (top since it is upside down) there was a hole about 1/2 diameter drilled into the lid to allow collected oil to escape. This upside down unit was put inside a plastic jar to catch the oil. It was quiet, and there was no mist on his tools, wood, etc., or in the air when he used it. Seemed to work great and he made in less than an hour.

Robert

Re: Robinair vacuum Pump

#11

Re: An easy filter

Mark Mandell - Gone Round In Jersey

>Sounds good!

And CHEAP too! |;-}}}}}}

mm

ps: don't forget a good seal around the inlet. Hot-melt glue should do fine.

m

Re: Robinair vacuum Pump

#12

Re: Robinair vacuum Pump

Michael Stadulis, in Gloucester County, NJ

>mark, do you have one....and is it noiser than a dry vane? -Mike

Re: Robinair vacuum Pump

#13

Re: Robinair

Mark Mandell - Gone Round In Jersey

>No, Mike, my current vacuum set-up is a pair of parallel-piped dehumidifier compressors (free from the appliance-guy/friend) that are rated/stamped at 2.6 cfm each. I have a spare sitting on the shelf in case one of the deployeds goes south, but the set-up does take up more shop space than a "real" vacuum pump would. I've looked at the oil-frees (Gast and Thomas) and the Robinair (my HVAC-dude uses them and swears by, not at, them). They provide more cfm with less noise than similarly sized pumps, and for a turner, CFM, not Hg", is where the focus should be. I've chucked a 20+" platter on an 8" vac bell pulling less than 10" of HG. with no problem on a 5 CFM draw. It's the small stuff that you need the high Hg. ratings for, and I don't do much in the way of small.

mm

Re: Robinair vacuum Pump

#14

Re: Robinair vacuum Pump

George Van

>Michael, I have the Robinair from Bernie. It is quite quiet and as Mark has said has a lot of CFM for the porous woods or the small bug holes and I am using too small of a pipe diameter at present to make full use of the pumps capacity. Bernie is a great guy to deal with!

Re: Robinair vacuum Pump

#15

Re: An easy filter

George Van

>Robert, that's a great idea, even I can afford it!

Re: Robinair vacuum Pump

#16

Re: Robinair vacuum Pump

Don Evans

>How does one contact Bernie regarding these units?

Don

Re: Robinair vacuum Pump

#17

Re: Robinair vacuum Pump

George Van

>Here it is. bernie@hydraulicparts.com