Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Super Resolution Thermal Imaging Camera

Jet mini lathe problems - help!

Posts

Jet mini lathe problems - help!

#1

Jet mini lathe problems - help!

Carol - now in NC Nebraska

>This is a reposting of a Jet mini lathe problem that was buried in an Indy Fest post.

I bought a Jet mini lathe a couple of years ago. The machine looked good in the factory box and the seller said it had light use. I am now getting a new definition of 'light use.'

The problem is in turning the tailstock handle. The rotation was very rough, almost impossible to turn through about 70% of a revolution. I had posted questions about how to get the thing apart and now have it in pieces.

It appears the male threaded portion of the tailstock spindle (leadscrew? on the exploded drawing in the owners manual) is BENT! The non-threaded portion is what is rubbing the inside of the casting. The threaded portions operate smoothly. In threading them together outside of the casting I noticed a slight wobble. Then I placed a straight edge along the part and definitely saw that it was bent. This cannot be good.

How did this happen? Somebody whaling on it to release a taper? But perpendicular to the shaft? Doesn't make sense. Seems like it would take some very serious pounding to bend this thing. What else should I check before I delve further into repairs? The motor runs fine. The headstock appears to runs true. Might there also be a problem with the tailstock casting?

Also, where do I get another part? On-line source? Or customer service number? The drawing is unclear about the part number. My thought is that it would be #56 which is listed on the parts list as the leadscrew, but is not identified on the drawing at all.

And assuming all I need is a new leadscrew, what do I use as a lubricant?

Re: Jet mini lathe problems - help!

#2

Keith Tompkins

Re: Jet mini lathe problems - help!

keith tompkins

>Carol, the piece can probably be straightened. If you don't feel comfortable attempting it, a decent machine shop can probably straighten it out. Hope this helps.

Re: Jet mini lathe problems - help!

#3

Re: Jet mini lathe problems - help!

Carole Valentine

>Technical Service

1.800.274.6846 - 7:30 a.m. to 5:30p.m.(CST, Monday - Friday)

Re: Jet mini lathe problems - help!

#4

Re: Jet mini lathe problems - help!

Carol - now in NC Nebraska

>Thanks, Carole. I'll call them in the morning.

Re: Jet mini lathe problems - help!

#5

Re: Jet mini lathe problems - help!

Carol - now in NC Nebraska

>Thanks, Keith, but for something that is listed at $6.33 plus shipping, if I found the right thing... Well, a machine shop is probably out of the question. :)

Still need lube info. White lithium? Axle bearing grease (I need some of that anyway)? Ask Jet?

Re: Jet mini lathe problems - help!

#6

So, why isn't it in the mail?

Ray Thompson - Middletown,IN

>The casting is probably ok. If it took that big a shock it would have either cracked or broke. If you want some practice, put a piece of wood under each end and a piece over the high side and introduce a good sized hammer. I'd bet the tailstock fell off and the handle took the brunt. If you don't want to mess with it, put it in the mail, maybe I can find someone to beat on it.

Ray

Re: Jet mini lathe problems - help!

#7

Re: So, why isn't it in the mail?

Carol - now in NC Nebraska

>Well, now that is a logical answer.

It will be in tomorrow's mail. It is not in today's mail because I did not get home until after the post office closed. ;) So I did not get it apart until an hour ago or so.

Thanks, Ray. You guys are the greatest.

Re: Jet mini lathe problems - help!

#8

Re: Jet mini lathe problems - help!

eaglesc

>make ssure there is enough clearance for the handwheel and the end of the tailstock.loosen the set scret unthread a bit and retighten

Re: Jet mini lathe problems - help!

#9

Re: Can you say"big catch!" The ...

Jamie Donaldson

>...part can possibly be straighten or at least replaced, and for lube get some wheel bearing grease or a tube of gear grease at any auto parts shop. Some farmer probably has a partially used tube that he would give you.

Re: Jet mini lathe problems - help!

#10

Re: Can you say"big catch!" The ...

Carol - now in NC Nebraska

>At home I have a small tube of white lithium grease. That is what I would use if I were home.

The operative word here is small amount. I have to move again next August! And the farmers buy this stuff is 5 gallon buckets! Of course, I could take a peanut butter jar and go get it filled....

Thanks, Jamie. I mailed the offending part off to Ray to see what he can do with it. I have other projects out in my "shop" here to tend to. A flower stand with a broken leg and a wood hauler to finish. After harvest season I will make a very large frame for an antique quilt. But the lathe has this calling song. Its in my head and I can't get it out. I hear there is no cure....

Re: Jet mini lathe problems - help!

#11

Re: Jet mini lathe problems - help!

Jorge Castaneda

>Lithium, molly (molibdenum) or graphite greases all good choices, just a light coating after a periodical inspect and clean.

Re: Jet mini lathe problems - help!

#12

Re: Can you say"big catch!" The ...

Paul Waddle

>Yeah,the lathe or tail stock was probaby dropped.I would just get a new part. Glad the head stock runs true,otherwise,I'd send it to Jet for reconditioning. If its not exactly right,you will think about it each time instead of enjoying your turning. JMHO,pw