Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

This $39 jig will make you a WOODWORKING GOD!

Indy Fest fallout

Posts

Indy Fest fallout

#1

Indy Fest fallout

Carol - now in NC Nebraska

>OK, folks.

I stopped along the way home picking up a few goodies. I got the BBQ light at a Lowes. I stopped at Woodsmith Store in Des Moines. It was the only toy store open when I was in the area. Drooled over their stuff for a while. Found the JT33-MT2 thingie there. Drove past a Woodcraft, I think in Peoria, but it was way past open hours. :)

Anyhoo. Now I have questions. I got an JT33 to MT2 thingie for my drill chuck. Tonight I went to see how it would all fit together. Well, the adapter slipped into the chuck just fine. But it did not slip into the tailstock just fine. :(

So, I started turning the tailstock wheel and that is where the problem is. It has a very tight spot about 70% of every revolution. I looked at the exploded drawing in the owner's manual to see what is what. I finally turned enough (very tight in spots) to get the tailstock spindle out. The threads look OK but it is very dirty in there. I see an E-ring in the drawing which appears to be holding the spindle in the casting. How do I get this out so I can eyeball and thoroughly clean everything? That would be part #57 in the drawing.

I bought this lathe used. It runs fine. I WILL get the VS motor running for it one day. (I promise, Randy.) All the bearings seem to run true and smooth. This is the only hitch thus far. I didn't get the live center, but thanks to Mike I now have one. I also didn't get a drive spur, but thanks to Jamie I now have one. Thanks, guys. I am not sure you are 'helping' as much as you are pushing me down the slope. LOL! But I am on a roll. ;)

BTW, the Hunter #3 is on the way, also.

So. What to do about the tailstock spindle to get it to turn smoothly and freely?

Re: Indy Fest fallout

#2

Re: Indy Fest fallout

Jennifer@Indy.USA

>Carol, first of all it was great to see you! Secondly...you ordered the Hunter #3! You dawg! :)

thirdly...what is the "JT33 to MT2 thingie for my drill chuck"? What are we talking about here?

Glad you made it home safe and sound.

Also, what mobile GPS system are you using?

Make sure you scan down the list a good bit. There's lots of fun pictures!

Jen

Re: Indy Fest fallout

#3

Re: Indy Fest fallout

Cyril Griesbach

>Jen, I think she's talking about a Jacobs Taper to Morse Taper adapter. My best guess would be that Carol has a drill chuck with a Jacobs taper and she wants to use it in her Morse taper tail stock.

Re: Indy Fest fallout

#4

Re: Indy Fest fallout

Carol - now in NC Nebraska

>"JT33 to MT2 thingie for my drill chuck"

It is a hunk of metal that has the male JT33 taper on one end for the drill chuck and the male MT2 taper on the other end for the tailstock. I had a brand new drill chuck left over from my new drill press (3 years ago) because I installed a large keyless chuck on the drill press. So for $10 the drill chuck is now usable on the mini lathe!

I had a hoot at Indy Fest. I am already planning how to come next year. It was great to see you again and meet all those wonderful folks. And Ray and Lynn - what's to say? Awesome!

My GPS is an Earthmate receiver with DeLorme software. The receiver plugs into the USB port on my laptop. I have an inverter plugged into a power point in the car to feed it 110 volts. I made a pedestal to position the laptop in easy view. I like the laptop screen much better the usual dinky GPS screens in the all in one units. Old eyes need larger pictures! My software is 3 years old and every now and again the position indicator is out in the toolies way off the road driving the program nuts because there is no road there according to the software! Guess I ought to upgrade.....

I've been looking at the pix. Gees, I'm getting thick! (Well, certainly not taller!) It is wonderful to put a face to a name.

Re: Indy Fest fallout

#5

Re: Indy Fest fallout

john lucas

>Carol If no one else answers you I will look at my Jet tonight and see if I can figure out what you are talking about. I have to work a ball game and won't get home until almost 10. The E ring will come off with a screwdriver but they will fly 30 feet when they pop loose so hold a rag over it or something.

It was really great finally meeting you. We all had a good time meeting everyone at Indyfest.

Re: Indy Fest fallout

#6

Re: Indy Fest fallout

Barry Elder

>Hi Carol,

I haven't had reason to dismantle the tailstock (yet) but, according to fig. 13, if A, B, and C are loose, the e-clip #51 needs to be removed like pulling a tooth. Then, if it's anything like my 1236, the whole assembly will slide out of the casting. I would suggest finding a replacement or two for the e-clip since chinese quality control is really bad and it probably will not fit as it should after it goes through the stress of removal. My two cents worth. I hope it helps.

Have a GREAT day!

Barry Elder