Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Veritas - Innovation in Tools

Sandblasting Equipment?

Posts

Sandblasting Equipment?

#1

George Balock

Sandblasting Equipment?

George Balock

>Okay, I'm interested in acquiring the ability to sandblast wood. Most of the products I see online are either the gravity fed or pressure fed devices. Both of these require lots of compressor volume at high pressures. What happens if I use these at lower CFM or pressure?

Re: Sandblasting Equipment?

#2

Re: Sandblasting Equipment?

Donna Banfield

>Hi George

I can offer my experience. I have a sandblasting cabinet, (it was given to me from a family member) and tried to run it using a smaller Porter Cable air compressor, the kind that is great for blowing chips out of your hollow forms, or for the brad nail gun.

Using that compressor to sandblast was an effort in futility. Within 3 seconds, the compressor would kick on, and need to run for several minutes before their was enough pressure in the tank to get another short blast -- and yes, it was a very short blast. Sandblasting a small piece (4" bowl) would take over an hour, after which your hand would be cramping from holding the gun and squeezing the trigger. It wasn't a pleasurable experience.

I've since upgraded to a Husquvarna 60 gallon compressor, 11 cfm, and have no problem. There is sufficent power to sandblast anything I can fit in the cabinet.

That's my experience, using the cabinet. I don't know about the type that you would use outdoors.

Re: Sandblasting Equipment?

#3

Re: Sandblasting Equipment?

Bruce Forrest

>Not that long ago I decided that I should try out sandblasting instead of wire brushing to texture some pieces. It was immediately apparent that without a cabinet it was not an indoor activity and given the Manitoba climate, it couldn't be an outdoor activity for most of the year either.

So I bought and assembled a stand-alone cabinet from Princess Auto ( in the $200 range as I remember.) I already had a nominally 4HP 14 gallon compressor. It works OK for short periods of time.

ie. It's a couple of minutes of blasting followed by a couple of minutes of waiting for the compressor to catch up. It's OK for now, but if you want to do a lot, or very large pieces, you'll probably want to get one of the behemoths (60-90 gallon) type compressors ($600-$1000)

Smaller compressors just can't deliver the continuous volume of air at high pressure which is required. As the previous post said, with very small compressors, it's a couple of seconds and then you might as well just blow on the piece for all the good you're doing.

Hope this helps.

Re: Sandblasting Equipment?

#4

another question

john lucas

>Does the type of gun have an affect on the outcome. I have 25 gallon compressor and would like to try sandblasting. Also I would assume the blasting medium would have an affect as well. I bought a really inexpensive gun from HF but haven't had the time to get any blasting medium and try it out.

Re: Sandblasting Equipment?

#5

Re: another question

Donna Banfield

>John, I'll take shot at trying to explain this, because when I first used my cabinet, this was an issue. Some of the guys from my club helped me out, and well, being guys, they just knew a lot more about this stuff than I.

We tried different nozzles with both larger and smaller openings. Smaller openings limited the size of media that you can use, so we thought larger nozzles would be better. If I recall correctly, the larger opening wasn't as effective as you'd think, because it required so much more pressure to push the media through the larger opening, with a force strong enough to etch your turning. Does this make sense?

I found that eventually upgrading to the larger compressor solved most of the problems that I was having. Maybe someone else can offer a different experience?

Re: Sandblasting Equipment?

#6

Re: another question

Pascal Oudet

>the bigger (=the highest power) compressor you have, the better.

for venturi type guns (succion fed) small nozzles will consume less air. but they won't be as powerful.

if you don't have a big compressor, and don't want to sandblast big pieces, try the "speed blaster" (google for this name, it's sold everywhere in the US, for example at amazon.com). it's a gun with its own abrasive tank above. the good point is you have a very regular output of abrasive, and it doesn't need a lot of air, and can work at relatively low pressure (4-5 bars). the drawback is you need to stop every minute to fill in the tank (a good point for your compressor). it works well for delicate work such as the one shown in the image below

I have a 3HP, 100l compressor (plus a home built bit blasting cabinet), it's not powerful enough for long sessions. the air supply should be around 36m3 @7bars /hour or higher if you want to work comfortably.

I'm about to invest in 400V power lines, to be able to run a 8-10HP compressor. I have some blasting ideas that I just can't do with the current compressor.

Pascal


img

Re: Sandblasting Equipment?

#7

Re: Sandblasting Equipment?

Mark Mandell - Gone Round In Jersey

>George,

The basic principal here is that air moves the sand - more air = more sand. The pressure of the air effects the speed at which the grains travel and the force with which they hit the target surface. Trying to do anything with less than 10CFM is largely an exercise in futility.

I have a 12 CFM compressor which is adaquate for touch-up blasting, and I use a gravity-feed gun I got from HF for $8. This is done outside, of course, well away from vehicles and the house. I use No. 2 sand as it's cheap and use the gun for turnings as well as spot-blasting rusted parts to be repainted. Note that you will beed protection for every inch of exposed skin and a good dust mask under your face shield. Long sleeve shirt, long pants, socks, gloves, the works or you will regret it. Note too that when the blast media hits the target surface, it breaks into smaller particles and removes even smaller bits from the surface. If you work in a blast cabinet, you can hook up the DC to take care of the fines, and the blast media gets recycled in the hopper. In the open, however, make sure that your filter mask is sufficient to protect you. Silicosis is not a fun condition to live with.

Re: Sandblasting Equipment?

#8

Thanks for the info. I'm looking forward this.

john lucas

>

Re: Sandblasting Equipment?

#9

Re: Thanks for the info.

Mark Mandell - Gone Round In Jersey

>John,

If you're looking for the "seriously weathered" look like Pascal's piece, get a blast cabinet set up so that your blast media is recycled. To produce that much wear on the wood in a free environment (outside), you'd have to go through a few bags of sand. It may be cheap, but it ain't dirt.

I've seen smaller benchtop cabinets for under $90 which should have enough capacity to do most any turning with better ones about double that. Bigger floor-standing units will run from $2-800, but will require increasing amounts of air. The guns wear mostly at the nozzels, so try to get one with a ceramic liner for longer life. Some will have changeable tips for different media (sand, beads, nut shells, glass, AO, SiO etc.) which come in grits that range like sandpaper does.

mm