Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Urban Salvaged Hardwood Slabs, Milled In-House from Rare Trees. Shop Unique Walnut Stock.

Travelling Buffer/Grinder System

Posts

Travelling Buffer/Grinder System

#1

Travelling Buffer/Grinder System

Allen Neighbors

>I set up my little Vicmarc for Buffing/Grinding when I travel, so I don't have to carry two more heavy motors along.

I used a piece of oak cutoff to make an arbor that would be held by my SN2 Chuck. I drilled a 1/2" thru-hole using my tailstock drill chuck. I used a spade bit to make a larger hole on the backside, to recess a 1/2" bolt head, and glued the bolt in the arbor.

I carefully turned down the face of the oak so the arbor would be the right length for my buffing wheels, the backing washer, the front washers and nut (I superglued a leather washer to the front washer to make the nut come off by hand).

Since this Arbor will double as a Grinding Arbor, I used my 1/6" parting tool and parted off a 3/8" thick "washer" from the front of the oak... this will be removed when the grinding wheel is installed, to allow for the greater thickness of the wheel with it's own washers.

This first pic shows the Arbor, with the wooden washer, the buffer backing washer, the front washer and nut. I marked the No. 1 Jaw so I will install it the same every time.


img

Re: Travelling Buffer/Grinder System

#2

Re: Pic 2

Allen Neighbors

>Shows the White Diamond wheel mounted and spinning. The flash stopped most of the action.

It's smooth as silk!

Re: Travelling Buffer/Grinder System

#3

Re: The forgotten Pic 2 

Allen Neighbors

>


img

Re: Travelling Buffer/Grinder System

#4

Re: Pic 3

Allen Neighbors

>This shows the Grinding Wheel mounted. You can see where I marked the Arbor, the Washer, and the Wheel label, so I can index it exactly every time, for balance. It works.

You can also see the wooden 'washer', removed, laying on the little lathe table, to the right of the wheel.


img

Re: Travelling Buffer/Grinder System

#5

Re: Pic 4

Allen Neighbors

>This shows the piece of white plexiglass resting in position to measure the distance the arm is adjusted from the wheel.

The arm is mounted on the same board the lathe is mounted to. This proves that the distance the arm is vertically from the wheel is not that important. I simply put the gouge in the varigrind, stuck it in the v-arm support, and slid the arm in, until the tip of the gouge was flat against the wheel. Perfect grind, every time.


img

Re: Travelling Buffer/Grinder System

#6

Re: Pic 5

Allen Neighbors

>I made a little wooden tool rest using a 3/4" dowel (to fit in the tool rest base) and a flat piece of plywood. You raise it until the tip is flat against the wheel... no tilting necessary.


img

Re: Travelling Buffer/Grinder System

#7

Re: Pic 6

Allen Neighbors

>This just shows the backside of the Vicmarc with the necessary tools mounted so they are handy, and I don't have to look in a box for them when needed.

Hope all these help someone get things together for travelling. :)


img

Re: Travelling Buffer/Grinder System

#8

Nicely Done Al! nm

tm

>

Re: Travelling Buffer/Grinder System

#9

Re: Travelling Buffer/Grinder System

john lucas

>Great job. That should be required reading for turners trying to get started on a budget.

Re: Travelling Buffer/Grinder System

#10

Very slick! A Shop Shots entry I think.

Eddie Pacheco, San Jose, Ca.

>Man, that's a wealth of effiecency in those pictures and setup. Just like that you helped this site kick butt over any magazine. Thanks!

Re: Travelling Buffer/Grinder System

#11

Re: Travelling Buffer/Grinder System

Allen Neighbors

>Thanks, John. That's what I'm on... a budget. :)

Can't afford an additional trailer to pull, and with all the turning cases, quilt cases, and fixtures, my space is limited.

Re: Travelling Buffer/Grinder System

#12

Re: Very slick! A Shop Shots entry I think.

Allen Neighbors

>Don't know if I did all that, but thanks, Eddie. :)

Re: Travelling Buffer/Grinder System

#13

Re: Travelling Buffer/Grinder System

Barbara Gill, Remlik VA

>I did something similar to that for my Mercury lathe. I set it up on the outboard side of the lathe. I mounted a Wolverine guide on the base so that I could keep the grind consistant.

Re: Travelling Buffer/Grinder System

#14

Re: Very slick! A Shop Shots entry I think.

don lewonczyk

>Very clever Allan, just goes to show what a person can do without if you have a good imagination but are also skilled in what you do. Your stuff works for me. DonL

Re: Travelling Buffer/Grinder System

#15

Re: Very slick! A Shop Shots entry I think.

don lewonczyk

>Sorry I misspelled your name Allen, I had a good friend named Allan and I guess thats what I was thinking when I posted, no offence intended. DonL

Re: Travelling Buffer/Grinder System

#16

Re: Pic 4

Jorge Castaneda

>Hi Allen,

You are a resourceful fellow, I like all your solutions.

A suggestion, just scribe, or dye the sliding arm and leave the plexiglass home...

Thanks for sharing!

Jorge

Re: Travelling Buffer/Grinder System

#17

Re: Travelling Buffer/Grinder System

George Van

>Very cclerver Allen, now i have a few more projects to complete. Thanks for taking the time to show us this!

Re: Travelling Buffer/Grinder System

#18

Steven Antonucci

I have a similar setup

steve antonucci

>minus the grinding wheel. In my original setup, I wanted to be flexible enough to switch and swap, but then I realized that's more trouble than it's worth, so I just made 2 dedicated wooden "holders". Saves having to find a wrench...

One has a buffing wheel and the other has a wire wheel that I use to texture. I find it easier to hold the object to a spinning wheel than a spinning wheel to the object.

Steven

Re: Travelling Buffer/Grinder System

#19

Re: Travelling Buffer/Grinder System

Pete in Holland, MI

>Nice ideas, BUT, pretty ballsy running a grinding wheel without a guard, especially one that will be mounted and dismounted often. I've been around grinding wheels a couple times when they've failed. BANG!....... and it's gravel all over the shop. Might suggest some sort of shield that can be placed to save your face.

Pete

Re: Travelling Buffer/Grinder System

#20

Re: Pic 6

ET

>Nice work, Allen. Tell us about the spring on the motor mount. Is it needed to tension the belt or does it do more to pull the motor to the right, holding the motor and pulleys in alignment. ET

Re: Travelling Buffer/Grinder System

#21

Thanks Allen. Made a PDF of the info for posterity

Craig Daymon

>I made a PDF file of your information. I'll see about sending it to you if you want to use it for a WoodCentral article.

-Craig

Re: Travelling Buffer/Grinder System

#22

Re: Pic 6

Allen Neighbors

>ET, the spring is not a really strong one, and as you guessed, it's holding the pulleys in alignment. The hinge that the motor is mounted on has just enough slack in it, that the tension on the belt causes them to be out of alignment. I have a Hand-grenade ring braised to the end of the hinge pin, making it easy to separate the motor from the lathe when I need to carry the lathe.

Re: Travelling Buffer/Grinder System

#23

Re: Pic 4

Allen Neighbors

>Thanks for the comments, Jorge.

I don't think marking the arm would do the job... because as the wheel wears the arm would be moved a tiny bit closer to the lathe bed. I hope I explained that right. I heard John Lucas explain the reason you shoudn't depend on marking the arm once, and I hope I remembered it right.

Re: Travelling Buffer/Grinder System

#24

Re: Very slick! A Shop Shots entry I think.

Allen Neighbors

>Thanks for the comments, Don, and don't worry about the spelling... I answer to just about anything. :)

Re: Travelling Buffer/Grinder System

#25

Re: Travelling Buffer/Grinder System

Allen Neighbors

>I originally intended to go on the outboard side, but the handwheel has left-handed threads, and I couldn't find out what they were, and even if I knew, I couldn't find a nut to fit, and I'd have to lengthen the spindle someway... anyhow, I think I just took the easy way out. :)

I just need to be sure that my tools are sharpened and ready before I stick a piece in the chuck, and remember to save one honed tool for the final passes. :)

Hmmm... that just adds -to a long list- some more stuff for an old guy to have to remember...