Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

ADVERTISE HERE - FREE TRIAL

Hollowing with Hunter Tools

Posts

Hollowing with Hunter Tools

#1

Hollowing with Hunter Tools

Bill Grumbine (Kutztown PA)

>Greetings all

After reading a number of testimonials to Mike Hunter and his carbide hollowing tools, I obtained a couple of the retrofit ones designed to fit in my Stewart arm brace. While they cut very nicely, I had some trouble - well, a lot of trouble - getting to the center of the piece on which I was working. I had been corresponding with Mike Hunter all the while, so I wrote him and told him the tool cut great, but it would be nice if he had one that cut straight on instead of to the side. Well, he has one, and he sent me one. I just got done hollowing out a tall narrow vase, and it works great!

I usually hollow these things with my bowl gouge as far as I can, and then switch to the Stewart tool with a teardrop scraper installed. Or, for really deep ones, I use my Monster hollowing tool from Randy Privett. But, the one I did tonight was hollowed for the last three inches down with the Hunter cutter. It is the same size as the one that retrofits the Stewart tool, but it has a 10� cant forward instead of a 30� cant to the side. This tip allowed me to hollow right down to the center of the bowl with very little effort, and as a bonus, I was still able to thin the walls down to where I wanted them without having to switch tips. I wrote Mike and told him that I did not know how many of these he had made up, but that he might want to make more!

Bill

Re: Hollowing with Hunter Tools

#2

Re: Hollowing with Hunter Tools

john lucas

>Bill That's my only complaint so far. Hollowing dead center. I drill out the center and then this isn't a problem. Of course that last 1/16 of an inch dead center where the drill left it's mark is still a little tricky.

I just hollowed a very old very dry hickory piece yesterday. I tried all of my hollowing tools just to see. The Hunter was easier on my and chattered less at the bottom. This was some hard wood. I kept getting nice curls with the hunter tool.

Re: Hollowing with Hunter Tools

#3

Re: Hollowing with Hunter Tools

Eddie Pacheco, San Jose, Ca.

>Bill, John, I noticed that when I used my Hunter insert on a shallow box I was making. Reviewing the catch I had I think it was because the insert had gotten loose. I was trying to remove the center cone I had created in my workpiece. Most likely due to my improper presentation of the cutter to the wood this allowed the wood to unscrew the cuter. Bill, I like your idea of canting the cutter forward in the holder by 10 degrees or so. I think I'll get my machine shop buddy to make a couple for me. I'm also going to get a holder for my Scorpion Hollower to try a larger hollow form. My first!

Re: Hollowing with Hunter Tools

#4

Dennis in Southern Oregon

Re: First attempt at woodburning and color

Dennis in Southern Oregon

>Bill, I am having a bit of trouble visualizing the orientation of this new Hunter bit. Could you post a picture or sketch? Dennis

Re: Hollowing with Hunter Tools

#5

Re: Hollowing with Hunter Tools

don lewonczyk

>I used the # 4 hunter to hollow out my first small box and had the same problem as you guys did. I first drilled to depth and hollowed down to the last 1/4" of drilled hole and was stopped dead with the hunter so I switched to my termite with small tip and it cleaned all the way down to bottom and made a nice gentle curve from bottom to sides. Not a computer whiz so I don't know how to post pictures but the box is 3 1/2" tall and 1 3/4" wide and made from mahogany. Don L

Re: Hollowing with Hunter Tools

#6

Re: Hollowing with Hunter Tools

john lucas

>I've had my best success turning away the central nub by flattening the presentation of the tool and coming up from the bottom, or rotating the tool so it's goes from 12 to 6 and coming at it from the left. Flattening the tool invites a catch so the 10 degree tilt that bill is talking about should help that.

Re: Hollowing with Hunter Tools

#7

What makes Hunter different from Eliminator, ...

Craig Daymon

>...New Edge Cutting Tools and any other carbide tipped turning tools? The pics of the Eliminator tools in the catalogs appear to have a good design. I have a big, 1" diameter cutter from New Edge Cutting Tools, which works OK...if I'm careful.

What differentiate the Hunter tool from the others?

I've heard so many people indicating how happy they are with it, but what makes it different from the other similar products?

Thanks,

Craig

P.S. Sorry for jumping in Bill.

Re: Hollowing with Hunter Tools

#8

Re: What makes Hunter different from Eliminator, .

john lucas

>Craig I've never seen an Eliminator live, only pictures. I would say the biggest difference is the round shank of the Hunter tool. Although mike has put a 35 degree slant on the tool you can rotate it to any degree you feel works. With the eliminator you would have to tilt it off the flat area. This might or might not be good I don't know since I don't own one. It appears as though it might have the same cutter. The Hunter is also considerably less expensive.

The other tools on the market have different cutters. I have only owned the Termite tool and can only compare to it. The hunter cuts as well or better and doesn't need sharpening. The termite is a little bit of a hassle to sharpen, you have to remove the tool from the holder, place it in another holder and then use the drill press or router to sharpen. It also doesn't hold an edge anywhere even close to the Hunter.