Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

This is the most versatile work station you will ever use

Reverse Chucking Tall NE bowls??

Posts

Reverse Chucking Tall NE bowls??

#1

Andy DiPietro

Reverse Chucking Tall NE bowls??

Andy DiPietro

>I turned an 8" tall natural edged bowl last night. It is 6" ID at the top point and 2.5" ID in the bottom. The bark edge is almost at 45 degrees. I rigged a wood jam chuck but the bowl wobbled too much.

Short of turning a stubby baseball bat, could I use a plastic pipe mounted to a chuck with a foam pad on the opposite end? What is a good technique for jam chucking this tall bowl form?

Craft supply sells a Bowl Chucker Pad at 6" dia. I would need a 3" diameter version on a shaft extension.

Thanks

Andy DiPietro

Re: Reverse Chucking Tall NE bowls??

#2

Re: Reverse Chucking Tall NE bowls??

Bill Grumbine (Kutztown PA)

>I think some guy is coming soon to help you with that Andy! Seriously though, in the meantime, I use a similar method to what you describe Andy, but I use my vacuum chuck without the vacuum for this. A number of people use a piece of PVC with padding on the end to accomplish this.

Bill

Re: Reverse Chucking Tall NE bowls??

#3

Andy DiPietro

Re: Reverse Chucking Tall NE bowls??

Andy DiPietro

>Bill,

Sorry, I could not wait another week for your demo. I had a beautiful piece of cherry burl begging to be turned last night. I will wait till after your demo to turn the second half of that burl.

I was hoping that you would answer this post. Just curious, what is the diameter and length of the vacuum chuck you use?

You should do a separate post on your upcoming demo at DelVal.

Thanks

Andy D.

Re: Reverse Chucking Tall NE bowls??

#4

Steven Antonucci

Oh no you didn't!

steve antonucci

>You cut your burl in half? I still have mine laying on the ground, waiting for inspiration.

Send me a picture when you have a second.

Steve

Re: Reverse Chucking Tall NE bowls??

#5

Re: Andy- those of us that use.....

Jamie Donaldson

>...jam chucks build a collection of sizes over the years, and you can do the same for very little investment in additional tools like vacuum systems. I have probably a dozen or more jam chucks that fit either my chuck jaws or are mounted on faceplates, and one of them is about a foot in length for use with pieces like yous. I have fitted them with pieces of dense foam on the ends to insure no marks on the bowl or slippage.

Re: Reverse Chucking Tall NE bowls??

#6

I Was Just Thinking

Barbara Gill, Remlik VA

>What if someone made a series of vacuum chucks for deep hollow vessels It could screw to the headstock? It would have the suction part at the end of a rigid tube. There could be an inflatable gizmo around the shaft that could hold the hollowform steady. I don't have the ability to make that kind of stuff, just come up with crazy ideas. :-)

Re: Reverse Chucking Tall NE bowls??

#7

Re: Andy- those of us that use.....

Sean Troy

>Jamie, where do you get the dense foam? I've been thinking of making some in different sizes. Thanks, Sean

Re: Reverse Chucking Tall NE bowls??

#8

Re: Sean- I use router/sanding.....

Jamie Donaldson

>.....pads and backpacking mattress foam pads, and 1 of those has been a lifetime supply!

Re: Reverse Chucking Tall NE bowls??

#9

Re: I Was Just Thinking

Don in Central Illinois

>That's not such a crazy idea. The one who taught me to turn, Keith

Adams, Decatur, IL, made a series of ends for this vacuum chuck. He made his out of the plywood used for the subfloor of bowling alleys. Very stable. He turns them to the diameters he needs and the length he needs. Hollows them with a forsner bit and glues some sort of rubber to help when using them as jam chucks. I do like the inflatable idea, cause I have a lot of problems getting them to run true.

Re: Reverse Chucking Tall NE bowls??

#10

Re: Andy- those of us that use.....

Barry Irby

>You can buy "Foamies" at Walmart. I think they are sticky backed but I'm not sure. Mouse pads also work well. So does the really cheap carpet pad for jam chucks, but not for vacuum chucks (it's porous).

You can also use the packing foam that is sort of clear, about an 1/8" thick and closed cell. The foam they put under laminate flooring may work. And you can Neoprene at gasket supply houses.

Re: Reverse Chucking Tall NE bowls??

#11

Re: Reverse Chucking Tall NE bowls??

Bill Grumbine (Kutztown PA)

>Andy, the bell on my chuck is 5" in diameter and about 3 1/2" long or so. It is aluminum. You may have seen it when you were here for the picnic. I can bring it along if you would like when I come down next week. Actually, now that I am thinking about it, I think it will be a good item to have for the demo.

Bill

Re: Reverse Chucking Tall NE bowls??

#12

Re: Sean- I use router/sanding.....

Sean Troy

>Thank you

Re: Reverse Chucking Tall NE bowls??

#13

Andy DiPietro

Re: Oh no you didn't!

Andy DiPietro

>Steve

Unfortunately the burl log section had rotted crack lines from the pith up into the center of the burl. Otherwise I would have been able to make a 14" dia. hollow form out of it.

So now I get to make two bowls and have some small left over burl pieces.

I sprayed water on the bowl before photographing it. It needs some adjustment on the bottom area, then sanding and finishing.

The wall thickness is 5/16" which is too thick. I am happy with it since it is only my fourth NE bowl that I have ever made.

Andy D.


img

Re: Reverse Chucking Tall NE bowls??

#14

Andy DiPietro

pic2 

Andy DiPietro

>


img

Re: Reverse Chucking Tall NE bowls??

#15

Dick Hines

Re: Andy- those of us that use.....

Dick Hines

>I like Bill use PVC. I have a set of reducers, 3"to4", 4"to5", and so on. I mount a short piece of PVC pipe in or over my chuck jaws so the reducer is extended from the face of the chuck. Then just bring up the tail stock and finish off the bottom.

Just to remember that your chuck is stronger than PVC and if you get to heavy handed with the key it will good by PVC.

Re: Reverse Chucking Tall NE bowls??

#16

Steven Antonucci

Two for the price of one

steve antonucci

>I'm debating buying a bowl coring unit for just such opportunities. Did you manage to core this?

How sweet is cherry burl?

Steve

Re: Reverse Chucking Tall NE bowls??

#17

Andy DiPietro

PVC End Caps on PVC pipe....

Andy DiPietro

>mounted to chuck jaws looks perfect for the job. Home Depot now sells 2' lengths of PVC pipe for a few dollars. I picked up 1.5" & 2" pipe plus end caps for less then $7.00 last night. The end caps have a perfect hemispherical shape that will not damage the inside of the bowl. I can cut several different lengths of pipe and interchange them with the end caps. Add some carpet padding and I am good to go.

Thanks

Andy D.

Re: Reverse Chucking Tall NE bowls??

#18

Re: PVC End Caps on PVC pipe....

Barry Irby

>Great Idea. I would still put some sort of pad in between the bowl and the pipe cap just to add some friction and to avoid slick spots and rim or edge marks on the wood. (DAMHIKT)

As Dick pointed out, a chuck will crush PVC. I have a couple of pieces I use and the jaws have marked the pipe. I put a No. 1 on the pipe so that the next time I mount the pipe I put that side back at the No. 1 jaw. Not sure I ever got mine to run perfectly true just by mounting it. I turned the end slightly to true it up and then put a pad over it to prevent marks in the bowl. IF you cannot get the pipe to run true you may not be able to use the end caps. Let us know. Great idea if it works.

I know some people do it, but I would never use the expanding function of the jaws to hold the Pipe. It is somewhat brittle and not very strong and might break. This is one of those things that never happens until it happens and then it is never good.

Re: Reverse Chucking Tall NE bowls??

#19

Andy DiPietro

Re: Two for the price of one

Andy DiPietro

>Hi Steve,

It would have been sweeter if I owned a coring unit.

That was the first piece of cherry burl that I have turned and it was a real pleasure. Thank you again for finding it. Just let me know when you want to go hunting again for some more wood.

Andy D.