Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Rare Exotic & Domestic Hardwoods, Milled In-House in Oregon. Browse Unique Stock.

buffing after oil, before waterlox?

Posts

buffing after oil, before waterlox?

#1

buffing after oil, before waterlox?

Mark Wollschlager

>I am working on a natural edged oak bowl.

I have 6 or 8 thin coats of Watco on it and intend to put some Waterlox on top of that.

It is sanded to 600 and not bad ( for me ), but I wonder if a buff with tripoli and white diamond before the Waterlox would help to improve the final look of the finish.

I am not after a plastic gloss look ( been there, done that ), so I will try for a satin sheen with the Waterlox.

Anyhow, is that a reasonable plan?

Thanks,

Mark.

Re: buffing after oil, before waterlox?

#2

which Waterlox?

tdaniel

>The red can product will be similar to the Watco; the green label will be more like a varnish. You might want to let your current oil dry for a couple of weeks or more and then wetsand to 2000 grit and then buff and wax. You may already have the finish you are looking for.

TD

Re: buffing after oil, before waterlox?

#3

Re: which Waterlox?

Mark Wollschlager

>The Waterlox is the original formula ( gold label with a red band) , medium sheen.

I am after a bit harder/durable finish that just the Watco and wax.

I do wet sand the final finish with 1200 or 1500 to level that off.

Mark.

Re: buffing after oil, before waterlox?

#4

Re: which Waterlox?

tdaniel

>the red label will give you what you want. Wetsand to 2000 grit and let dry before putting the Waterlox on. Give it several coats of the Waterlox and then let it dry thoroughly before buffing.

Re: buffing after oil, before waterlox?

#5

Steve Kubien

Re: which Waterlox?

Steve Kubien

>TD, what do you wet sand with? More of the Watco I assume? curious as I am just starting a few pieces with a danish oil similar to Watco.

Thanks,

Steve Kubien

Re: buffing after oil, before waterlox?

#6

Re: which Waterlox?

tdaniel

>Steve, once you have worked enough oil into the wood all you need to do is sand with water. It is ok to sand with the oil but not necessary. The reason that I sand with Watco instead of Waterlox is that the Waterlox dries too fast. So sand with Watco or water, either will work.

Re: buffing after oil, before waterlox?

#7

Steve Kubien

Thanks

Steve Kubien

>

Re: buffing after oil, before waterlox?

#8

Ric Taylor

Re: buffing after oil, before waterlox?

Ric Taylor

>Mark,

I use the same Waterlox that you mentioned, Original, yellow can with a red band, medium sheen. You didn't say whether you have used this before, but it sounds like you are expecting a less-than-glossy finish.

As I said, this is what I use, usually two or sometimes three coats. I buff after each coat with tripoli and white diamond, unless the wood is dark and porous like black walnut, then I skip the white diamond. After two coats, the finish is quite glossy. If I put on three coats, it shines like glass.

And contrary to popular belief, you only have to wait 24 hours after applying a coat of Waterlox before buffing and applying another coat, even if you live in one of the highest-humidity areas.

I suggest you Google Andy Chen's article on applying a Waterlox finish. His easy method is right on.

I don't know about applying Waterlox on top of another finish, I haven't done that except I sometimes do apply it over sanding sealer.

Ric

Re: buffing after oil, before waterlox?

#9

Re: buffing after oil, before waterlox?

Mark Wollschlager

>I have used the Waterlox before, and I read Andy Chen's article at the Gulf Coast site, thanks for the pointer.

After looking at the Waterlox web site I may go by Woodcraft tomorrow and see if they have any of the Satin ( brown label ) in the trial size packets.

The end result using the red label product was very nice and clear.

The 'plastic' nature of the finish was noted by some ( non woodturning ) friends of the recipient. Perhaps too many coats were applied.

A watco - buffed wax finish is nice, this piece will probably end up in a pretty high humidity area and waxed surfaces don't last really well.

Touchups might be a good excuse to visit in the future. :-)

Mark.