Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Build it. Rock it. Rockler has your woodworking tools.

Hollow form rechuck

Posts

Hollow form rechuck

#1

Hollow form rechuck

ryker acuna

>How do I go about rechucking this thing? I alcohol soaked it and left the bottom half 1/2inch thick. This will leave enough to rechuck but Im not to sure with the natural edge on top. Any ideas? I cant figure it out. thanks

R


img

Re: Hollow form rechuck

#2

Re: Hollow form rechuck

Carole Valentine

>Ryker, I have turned a tapered cone that fits in the neck then narrowed the area of the cone where the natural edge is so it doesn't get damaged ( sort of an egg shape) Bring up the TS for support and turn your base. You will have to remove the leftover support nub on the bottom after you part it off. Sometimes I use a little square of rubbery shelf lining material to add to the grip power of the cone. Either way you will have to hit the contact point with a little fine sandpaper before finishing. Others will probably have some good suggestions.

Re: Hollow form rechuck

#3

Re: Hollow form rechuck

Bill Grumbine (Kutztown PA)

>Ryker, a tapered cone that Carole describes is a good way to finish most hollow forms. I can see where that might be a problem with this one. The compression needed to make it spin could very well crush it. I do not know the origination of the technique, but a man local to me gave us a good solution that will work for you, and is very similar to what Carole proposes. It is called the Kirtsen Cone, and I learned it from Kim Blatt.

Take the cone Carole describes, and run a shaft through it, with a pad on the bottom. The cone fits into the neck of your hollow form to center it, and the shaft with the pad contacts the inside bottom. That allows the driving force to be at the bottom of the piece between centers without stressing the rest of the form. You can now turn the tenon away without crushing the piece.

Good luck with it, and if this is not clear, let me know and I will try to clarify it for you.

Bill

Re: Hollow form rechuck

#4

Re: Hollow form rechuck

Barry Irby

>I go at it the "other way". I made a stick that has a Morse taper on it that fits into my head stock. A shoulder on it bears against the end of the lathe's shaft. The stick is long enough to reach the bottom of the HF and slender enough to pass through the opening. If the stick is too slender, I wrap tape around it. I use the same stick over and over. Anyway, When I make an HF I leave the center mark on the bottom. Then I reverse chuck it so that the top is near the headstock and I bring the tailstock up against the bottom and press it against the stick. Same concept that Bill mentioned. If necessary I pad the bottom with carpet pad or shelf liner like Carol said to add friction to drive it. Since the stick is directly opposite the tailstock's live center you can really crank down on it without fear of it crushing. Then you turn away the bottom except for a little nib that you remove by hand. Then you claim it was handmade.

Re: Hollow form rechuck

#5

Re: Hollow form rechuck

Bill Clark

>Don Pencil now sells a "Multi-Purpose Jamb Chuck" as described above. Here is a picture on one with a hollow vessel chucked up in a lathe. Note the cone in the opening holding the vessel centered while the shaft inside pushes against the revolving tailstock.


img

Re: Hollow form rechuck

#6

Re: Hollow form rechuck

Norm Smith in Nova Scotia

>Riker, I use the large cone that came with my live center in reverse. It fits over the opening rather than in it. If you do not have one you could turn one with a spigot to fit your chuck. Just put your piece in the cone and bring up the live center. True a spigot on your HF and reverse. Hope this helps.

Norm

Re: Hollow form rechuck

#7

Re: Hollow form rechuck

Russ Babbitt Jr.

>I got a Kirsten Kone from a member of the San Diego Woodturners. I do not know if he is still making them.....you could try contacting them.....

Re: Hollow form rechuck

#8

Re: Hollow form rechuck

ryker acuna

>Thanks for all the advise. Im a member of the san diego woodturners, however they have moved the club meetings so far on the outside of (San Diego) that it takes to much gas to drive there. Anyway I will look into the Kirsten tool and use all the tips provided by all you experts on the panel. Once again you all helped tremendously. thnx.

R

Re: Hollow form rechuck

#9

Woodchucker mandrel

Dave Staeheli

>Craft supplies sells a "Kirsten Cone". Part # 995-6000. Made by "Woodchucker"? I made mine after seeing Mike Mahoney use one in a demo years ago. First I'd ever heard of it. Actually made three. My best one, I made out of about 18 inches of 3/4" aluminum rod. Was able to turn a morse taper on it on the wood lathe. I use a small 1" sanding mandrel socketed in the end for a driver.

A little off subject. The second mandrel I'd made came to a bad end. My neighbor needed a jack handle and was rummaging around in my shop for a steel rod. Finding my mandrel, he thought he had it made! Returning it, he was sorry he bent it. Not as sorry as I was.

Re: Hollow form rechuck

#10

Re: Hollow form rechuck

don lewonczyk

>Don Pencil. com has a new multipurpose jam chuck and centering ring on his web site. jam chuck JC100 is $34.95 centering ring $14.95, look at the pictures and you will see what Carole and Bill were telling you. Looks pretty neat and a problem solver. I'm no way connected to Don other than ordering some of his goods which are of good quality. The man that made his own is along the same quide lines only Don's #2MT shaft is made from steel and you might get away with using it for a jack handle and not bending it. I'm joking about the jack thing, any tool that makes a man or womans live easier deserves respect. Hope you make it happen, let everyone know the results. DonL

Re: Hollow form rechuck

#11

Re: Hollow form recheck

Barry Irby

>That is the same concept as mine. I did not think of the cone, but the drive mandrel is the same idea. Mine is better though, I named it Dicky the Stick in honor of Johnny Carson. (Some of you are too young to remember and the rest are too old). Also, mine did not cost $35. OTOH, I had to make mine. What a horror. Making something useful on the lathe. I'd rather be making something on the lathe. Oh, wait, that's the same thing. What would I be doing if I weren't turning something on the lathe, I know, I know.... I'd be turning something else.

Actually Dicky has a dimple in the end and I intentionally leave a little nib in the bottom of the vessel and the nib inserts into the dimple and helps center things up. I don't do this on "open" vessels where it is easy to see the nib.

I like the cone idea and may try it. OTOH, the tape I use on mine does not mark the vessel. Hmmm.

Re: Hollow form rechuck

#12

Re: Hollow form rechuck

Bill Hale

>Ryker

I start all of my pieces between centers and this provides a bottom center point. As to rechucking this form I have many jig pieces of many lengths and diameters.

My jigs are nothing more than jaw chuck mount on one end and a long round piece on the other end. The piece is mounted with the long round piece going to the inside bottom of the piece to be worked and the tail stock live center put into the outside bottom center mark provided by the first mounting. I put a piece of cloth between the jig and the inside bottom. This helps prevent a burn mark if the jig turns and the work piece is stopped by your tool pressure.

This is how I finish the bottom of all of my work. When you finish cleaning off the bottom you are left with only a small center tit that can be sanded or trimed off.

Feel free to E-Mail me if this seems confusing.

Good turning and be safe

Bill in Show Low, AZ.