Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Find a woodworking club near you

Found belts for Jet Mini Lathe and other tools!

Posts

Found belts for Jet Mini Lathe and other tools!

#1

Found belts for Jet Mini Lathe and other tools!

Larry In Lima

>I just wanted to pass this information on. From time to time, I see somebody here looking for belts for tools. I was looking for an inexpensive (but good quality) belt for my Jet Mini Lathe, as well as a drive belt for a very, very small bandsaw that I have. I came across a place called "The Belt Store", http://www.beltsforanything.com.

Checked out their website, said the heck with it, and called them. Figured they knew what I needed better than I did ;) .

Phyllis (didn't get a last name), was great. Knew exactly what I needed and had it, prices were great. Just over $7.00 for the lathe belt, and $4.50 for the bandsaw drive belt. Got them by postal mail, very cheap shipping, and they actually fit just right!!

I'd recommend that everyone get a spare if you don't already have one for your lathe. Simple things will stop your turning faster than anything!!

Very pleased with their service and prices. No affiliation or relation to them, yada, yada, yada... Larry

Re: Found belts for Jet Mini Lathe and other tools!

#2

changing the Belt on a JET mini.

Jennifer@Indy.USA

>I know I'm just flirting with disaster with my JET. It's nearly 9 years old and I've never changed the belt. My question is...how much of a disassembly is it to change one? Is it a pain to do? I don't suppose there a little link belt that would do the trick is there?

Thanks for the link and any info you might have!

Jen

Re: Found belts for Jet Mini Lathe and other tools!

#3

Re: changing the Belt on a JET mini.

Larry In Lima

>This is right out of the manual, they sort of "make" extra steps really..... Mostly it is just a matter of taking a good look at things while you do the first half of this, then reversing the process to "reassemble". hth - Larry

1. Disconnect the machine from the power

source (unplug).

2. Open the access doors at the left side of the

base on the back side of the headstock

3. Loosen the motor plate lock handle. Lift up on the

motor plate handle to take tension off the belt.

4. Loosen the set screw on spindle pulley (upper).

5. Loosen the two set screws in handwheel.

Unscrew the handwheel while holding onto the spindle.

6. Remove handwheel and pull the spindle out

while holding onto the spindle pulley.

7. Place the new belt on the spindle pulley.

Place the spindle pulley back into the

headstock the same way it was removed.

8. Insert the spindle into the spindle pulley

aligning the key.

9. Thread the handwheel onto the spindle

leaving a little space between the

handwheel and headstock. Tighten set

screws.

10. Center the spindle pulley and tighten set

screw.

11. Wrap the belt around the motor (lower)

pulley. Be sure the belt is aligned with

spindle pulley and motor pulley.

12. Tension the belt and tighten the motor plate

lock handle.

Re: Found belts for Jet Mini Lathe and other tools!

#4

Re: Found belts for Jet Mini Lathe and other tools

WayneLeach - NW Ont

>Larry,

Good info-thanks a bunch!

Would you happen to have a part number for the Jet mini belt??

Wayne

Re: Found belts for Jet Mini Lathe and other tools!

#5

Re: changing the Belt on a JET mini.

Mike Rubes, Apex, NC

>Hi Jennifer,

I've changed the belt on my Jet mini and it really wasn't a problem. In fact, I've pulled the headstock apart a few times to grease things up to try to keep it running smooth. The directions provided are good, it really isn't much of a hassle to do.

After I got the hand wheel off, I did have to use a deadblow mallet to gently tap the spindle out and then again to tap the spindle back into place. But it really was just a few slight taps.

Good luck!

Mike

Re: Found belts for Jet Mini Lathe and other tools!

#6

Hmmm, sounds easy enough! Thanks!

Jennifer@Indy.USA

>

Re: Found belts for Jet Mini Lathe and other tools!

#7

Re: Found belts for Jet Mini Lathe and other tools

Allen Neighbors

>Good stuff! I ordered a belt for my VL100 via email. She sent it to me in Colorado. Very good, fast, economical service!

Re: Found belts for Jet Mini Lathe and other tools!

#8

Re: Found belts for Jet Mini Lathe and other tools

Larry In Lima

>Wayne, it is 240J3. Hth - Larry

Re: Found belts for Jet Mini Lathe and other tools!

#9

Re: Found belts for Jet Mini Lathe and other tools

Allen Neighbors

>240=length

J=distance between points of the grooves

3=number of grooves/points

That's the way she explained it to me.

Just info.

Re: Found belts for Jet Mini Lathe and other tools!

#10

Re: Should have clarified the J...

Allen Neighbors

>J= .092 inches

Re: Found belts for Jet Mini Lathe and other tools!

#11

Thanks Larry&Allen for the info

WayneLeach - NW Ont

>