Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Reach the woodworkers who ACTUALLY BUY

Sanding inside of hollow forms tip *Pics*

Posts

Sanding inside of hollow forms tip *Pics*

#1

Sanding inside of hollow forms tip *Pics*

Ron in Drums PA

>


All I do is CA glue some sandpaper to the tip and sand away.

Re: Sanding inside of hollow forms tip *Pics*

#2

Re: Sanding inside of hollow forms tip *Pics*

Norm Smith in Nova Scotia

>Ron, great idea. Thank`s

Re: Sanding inside of hollow forms tip *Pics*

#3

Re: Sanding inside of hollow forms tip *Pics*

Carole Valentine

>Good idea Ron. Not sure where I would find these around here - an office supply store or a drug store, hopefully.

Re: Sanding inside of hollow forms tip *Pics*

#4

Re: Sanding inside of hollow forms tip *Pics*

john lucas

>Office supply stores carry them They are called Finger cotts.

Re: Sanding inside of hollow forms tip *Pics*

#5

Re: Sanding inside of hollow forms tip *Pics*

Mark Kauder, Phenix City, AL

>Sure would beat CA glueing sandpaper right on your finger. ;)

and probably much safer than using a latex glove.

Mark

Re: Sanding inside of hollow forms tip *Pics*

#6

Re: Sanding inside of hollow forms tip *Pics*

Wally Dickerman in Arizona

>Been using these for years. I'm wondering why you glue the sandpaper to the tip. I just triple fold a small piece of sandpaper and quickly go from one grit to the next. Triple folding puts sp grit against the rubber and helps to keep it from slipping. Works great.

Wally

Re: Sanding inside of hollow forms tip *Pics*

#7

Re: Sanding inside of hollow forms tip *Pics*

Ron in Drums PA

>Wally:

"I'm wondering why you glue the sandpaper to the tip"

� The tips are cheap.

� When I tri-fold the sand paper, it seems to slip a bit. This way I always know where the sand paper is.

� If I lift my finger a bit, the paper stays with me

I use 5 with different grits, 100, 150, 250, 320 and 400. When the paper gets dull I just rip off the paper and CA glue fresh paper. I started doing this over a year ago and I'm still using the 5 tips that I started with.

Carole:

I bought them at a Staples, I think I paid a buck or 2 for a box of 12

Re: Sanding inside of hollow forms tip *Pics*

#8

Re: Sanding inside of hollow forms tip *Pics*

adrien

>Not sure John, but those tips appear to be considerably stronger than the thin latex finger cots which I don't think one could pull a glued piece of sandpaper off of. (Don't end a sentence with a preposition.)

Re: Sanding inside of hollow forms tip *Pics*

#9

Re: Sanding inside of hollow forms tip *Pics*

Carole Valentine

>They are. I just went and got some (same kind) I have not tried them yet but I am wondering if you don't have to use more than one layer of sandpaper because of the bumpies on the finger thingie. Will let you know.

Re: Sanding inside of hollow forms tip *Pics*

#10

Re: Sanding inside of hollow forms tip *Pics*

Ron in Drums PA

>All I use is one layer, it works.

Re: Sanding inside of hollow forms tip *Pics*

#11

Re: Sanding inside of hollow forms tip *Pics*

Wally Dickerman in Arizona

>Triple fold it. Then you can quickly bring up fresh grit. Triple folding it also helps control heat.

Wally

Re: Sanding inside of hollow forms tip *Pics*

#12

Re: Sanding inside of hollow forms tip *Pics*

George Van

>Thanks for the tip Ron, it is very timely as my interest in hollow forms increases!