Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

REAL MILK PAINT

techniques for beefing up punky wood

Posts

techniques for beefing up punky wood

#1

techniques for beefing up punky wood

john pickett

>I just rough turned an awsome sycamore bowl (sorry, camera is broken) but it has a streak through it which is just on the punky side. Any ideas to beef up this section. I haven't had too much trouble so far, but I have not started the final cut.

Re: techniques for beefing up punky wood

#2

Re: techniques for beefing up punky wood

Jennifer@Indy.USA

>Wally Dickerman suggests 50/50 mix of water and white glue. Soak it, drain it and let it dry.

John Jordan suggests that "life is too short to turn crappy wood" and to pitch it...but I know that's hard to do when it's mostly solid wood.

Good luck with it.

Jen

Re: techniques for beefing up punky wood

#3

Re: techniques for beefing up punky wood

john pickett

>Thanks. Sometimes wood that is just over the edge can be really nice.

Plus, sometimes its not obvious that it is so extensive until you have invested several hours

Re: techniques for beefing up punky wood

#4

Re: techniques for beefing up punky wood

Dale Cook

>Hi John, depending on your final finish I've used thinned down lacquer to firm up the wood. It dries fast and you can cut a-little and add more as needed. Good luck.

Re: techniques for beefing up punky wood

#5

Re: techniques for beefing up punky wood

john lucas

>John I use lacquer thinned 50/50 with lacquer thinner. I brush or pour some on, let is soak in and then pour more on. I let it dry and do a test cut. If it doesn't cut well I put more on. sometimes it takes quite a bit and it will take a good while to dry but it hardens up nicely. The downside is, not all finishes will work with it but many will. I use lacquer as a finish so it works great with that.

If it's not terribly punky and your just getting tearout, coat it with a layer of Johnson's paste wax and try a cut. Sometimes one or two coatings and passes with a really sharp tool are all it takes.

I'm dying to try wally's technique but just haven't had the right piece of wood yet.

Re: techniques for beefing up punky wood

#6

Re: techniques for beefing up punky wood

GaryG in MD

>John,

If you're interested in a commercial, water-based product, "PC-Petrifier" works well. It's not overly expensive at $8/pint (a lot cheaper than CA glue!). You can get it at a number of brick&mortar stores or online. It works nicely on spalted wood that has gone a little over the edge.

Soak & Save, Gary

Re: techniques for beefing up punky wood

#7

Just don't get it near your computer! 8^]

Gary Evans Tallassee, TN

>

Re: techniques for beefing up punky wood

#8

Re: techniques for beefing up punky wood

Gary Evans Tallassee, TN

>Hi John,

Two things: Like thinned lacquer, you can also use thinned oil-based polyurethane to strengthen the area. I use the mineral spirits that I clean my poly brushes in. Like John Lucas suggested, it may create issues with whatever your finish will be.

You can also use thinned shellac. If you use the dewaxed version, you can put any finish over it.

Gary

Re: techniques for beefing up punky wood

#9

MinWax Wood Hardener

Ralph

>

Re: techniques for beefing up punky wood

#10

Tung oil sealer from Lee Valley

Charles R. Smith from Victoria

>I've had wonderful success using the tung oil sealer that is sold by Lee Valley. I poured it into several rough-turned bowls in which the Minwax/wood hardener products didn't work nor did a 50/50 solution of white glue and water. I poured a goodly amount of it into the roughed-out bowls and let it soak in and dry for several days before doing the final turning. The resulting appearance was worth the effort (and the expense of the stuff).

Charles

Re: techniques for beefing up punky wood

#11

How about water based poly?

Carole Valentine

>I'm currently working on piece of punky box elder and don't want it to darken. I wondered if anyone had tried the WB poly. I will after dinner. I never had much luck with the 50/50 white glue process.

Re: techniques for beefing up punky wood

#12

Re: How about water based poly?

George Van

>Carol, ultra blond shellac in a 1# cut will help strengthen punky areas and leave the wood quite natural. I do however get better results if necessary with thinned Deft, which is like the old airplane glue.

Re: techniques for beefing up punky wood

#13

Re: How about water based poly?

John Veerkamp

>deft is a lacquer, so I assume other lacquers will work also.

Re: techniques for beefing up punky wood

#14

Re: How about water based poly?

Carole Valentine

>Thanks, George. I use those on other woods but I have not had much luck with shellac or lacquer not imparting a slight amber tone on very light woods.