Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

ADVERTISE HERE - FREE TRIAL

Jamison system limitations

Posts

Jamison system limitations

#1

Aage Rendalen

Jamison system limitations

Aage Rendalen

>I recently bought the Jamison system, and I'm having trouble getting under the shoulders of Southwestern type HFs. The back gate imposes limits on the angle of the boring bar, and for deep shoulders I've had to pull out my manual Kelton hooks to get in as deep as I want.

I've looked at the end of the boring bar cut at 45 degrees but it does not seem very promising to me.

How do the rest of you deal with these deep-shouldered vessels?

Re: Jamison system limitations

#2

Re: Jamison system limitations

Sean Troy

>Can't you move the gate away from you so you can get a larger angle?

Re: Jamison system limitations

#3

Aage Rendalen

Re: Jamison system limitations

Aage Rendalen

>Even when I swing the back gate as far over as will go, I'm having trouble. Sorry about accidentally posting twice the same message.

Re: Jamison system limitations

#4

Re: Jamison system limitations

Sean Troy

>Sounds like you'll need a swan neck/ curved bar holding your cutter.

Re: Jamison system limitations

#5

Re: Jamison system limitations

john lucas

>I agree with Sean. I have the same problem with my homemade jamieson boring bar. I have made curved bars like John Jordan but the tip still won't reach under certain vessels. I have used the Sorby swan neck tool with fair success. I don't like the cutters but by twisting them sideways you can reach a lot of areas. I'm going to build a John jordan style curved bar but I'm going to mount the cutter at about 45 degrees on the tip instead of coming straight out. That should reach those hard to get to areas.

Re: Jamison system limitations

#6

Re: Jamison system limitations

Mark Kauder, Phenix City, AL

>I use my Keltons in my Jamison system. Have not had a problem yet. I if I can get to it with a hand held tool, that same tool in the Jamison will work. Sometimes you have to turn the D-shaped bar over the other way.

Mark

Re: Jamison system limitations

#7

Lyle Jamieson

Re: Jamison system limitations

Lyle Jamieson

>Hi Aage,

Sorry to hear you are having difficulty, and for my tardy reply. I dont frequent these sites. The Jamieson system allows you to have access to any shape that can be done with any other tool system...only easier. The swivel assembly allows infinate control to position the cutter to reach around the neck openings close to the hole and shoulder area of hollow forms.

The three options available with my hollowing system will get the rest of the shape you want to hollow.

(1)The straight in the end, swivel assembly has its limits for reaching around inside shoulders, but it is needed for long tall shapes.

(2)The 45 degree hole on the other end of my bar for the swivel assembly can reach around shapes that are bigger in diameter than they are tall. This option has a learning curve. The back rest position has to be moved on angles and even sometimes moved 180 degrees to get the opening area and thread the tool into small holes. Some fiddling sometimes but all possible shapes can be reached. Its worth the fiddling because it is easy work and will not destroy your body in the process.

(3)The third option and one that might be new to some of you. Is the bent 3/8 diameter shaft swivel tip assembly. I use this attachment for most of my hollowing. I can get into smaller holes easier and yet reach most shapes. Picture a sphere shape with a small hole. The bent holder can reach up under the shoulder with much less swinging of the handle and the back rest usually can stay in the original neutral position.

I have designed my system to reach any shape you want. I offer classes as I travel around the country frequently, to kick it up a notch and tackle advanced techniques. Also, I really want all my turning family to be having fun with my system. Why do we turn anyway...to enjoy the lathe and process. If you are not having fun with my tools, call me 231-947-2348 and we will trouble shoot your process and remove the obstacles. E-mail is only one way comunication. I hope this helps. Regards, Lyle

Re: Jamison system limitations

#8

Re: Jamison system limitations

Allen Neighbors

>Aage, I made two little 3/8" dia bent-necked tools... one will reach further than the other one. With them I can hollow far enough inside the opening, to allow me to use other tools to get the rest of the way to the shoulder.

Re: Jamison system limitations

#9

Re: Jamison system limitations

Joe Flemig

>And that is one of the advantages of a Stubby lathe :-)

Joe Fleming - San Diego

Maybe rebuild your capture system to make the slot extend several more inches to the rear of the lathe.

Re: Jamison system limitations

#10

Re: Jamison system limitations

Don Evans

>Hi Lyle:

I recently upgraded from a Nova 3000 to a OneWay 2436 and had pretty much decided on your system as I must upgrade my hollowing tools also.

Your number 3 option confused me though, are you saying there is now a straight shaft that is 3/8" diameter that can be used instead of the 3/4" shaft? If that is correct, will the end holders both straight and bent models fit into this 3/8" bar?

Don

Re: Jamison system limitations

#11

Lyle Jamieson

Re: Jamison system limitations

Lyle Jamieson

>Thanks for your question so I can clarify.

Refer to the Packard catalog. Number 105805 Page 16 is the bent swivel assembly I referred to. The photo has the cutter in the wrong side, but thats another thread. It fits into my boring bars to reach around corners and get into smaller holes that are not much bigger than the boring bar itself. I have them for sale (are there rules I should not solicit here??)from me direct and you have the option of getting a new bent assembly or just the 3/8 bent shaft and exchange the swivel assembly from your straight swivel holder. All parts are interchangeable. Call me to place an order. 231-947-2348

I have made, for my own use, smaller boring bars to get into small items like Christmas ornaments. But they are too expensive to manufacture for production and sale to others. I find the supported system still works the best because I have fingertip control and the laser to get thin uniform walls. You can get some made for yourself as cheap as I can, and adapt them to the support handle or extend them out from the 3/4 bar with a machined 3/8 tenon. I super-glued 3/16 HSS cutter tips on the angle desired. They only need to be 5-7 inches long, 3/8, 1/2, or 5/8 inch dia. Dont hesitate to call me for details if you want to try these.

The problem with these small shafts are the cost, and they cant get extended over the tool rest very far without vibration. So I usually cheat and do Christmas ornaments with the 3/4 boring bar through a larger hole and use the finial base to cover the hole.

Hope this helps.

Regards,

Lyle

lylejamieson.com

Re: Jamison system limitations

#12

Re: Jamison system limitations

Don Evans

>Thanks for clarifying, it all makes perfect sense now that I know the tool holders are 3/8".