Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

This $39 jig will make you a WOODWORKING GOD!

Reflections from my first demo (long)

Posts

Reflections from my first demo (long)

#1

Reflections from my first demo (long)

Doug Thompson near Cleveland

>The first time is always the hardest and I'm glad it's out of the way.

I was asked by a friend Gordon Seto to demo at a club meeting about 50 miles away. The first reaction was to say no and take the easy way out but all you can do is take a deep breath and go for it.

I was surprised how much prep was involved to put on a demo, it's one thing to turn at home but to take everything you need to a different location takes a lot of thought. Each item has to be available and it's the little stuff that's easy to forget. Gathering the wood is a chore by itself, to find the wood at the last minute so it's green and prep the blanks takes time.

When you get to the location that's when the club members step up to the plate, you have more help than you could ever want. From unloading the truck to the setup everything is done for you which shows the charater of the club members. To each and everyone person that was there I say thank you.

The demo is what you what you know (hopefully) the hard part was talking and trying to discribe and remember what you were going to high light about each step. Overall it when ok, the hat was still in one piece at the end of the demo but it did weigh about 2 oz's more than expected, that was a surprise. When I got home I tried to figure out why it was so heavy, recheck the calipers they were ok then remembered I didn't let it dry on the lathe befor topping it off... that could be the extra weight. it's to late now.

Here's what I'd do different.

Lay all the equipment on a table in clear view so it was easy to find. The table was twice what I needed but I only used one corner of it.

Don't change tools for a demo. I changed to blades in the handles the day before and didn't have the grind quite right. The entire demo I forced the cut and couldn't correct it.

When you have the tool on the wood don't think of what your going to say next. I almost made a fatal mistake when my brain went into la la land thinking of what to say next.

I felt a little nervous but it wasn't that... you feel self-conscious because everyone is looking at you!

This is getting long, I would like to thank the Buckeye woodturners for everything... it was fun.

Re: Reflections from my first demo (long)

#2

Re: Reflections from my first demo (long)

Brian Hahn in SW Wisconsin

>Congratulations on your successful demo.

Most people don't realize how much work is involved to prepare for a demo. I find preparation takes anywhere from 4 to 10 times longer than the actual demo.

Having a spot to lay out your tools and supplies is really nice. At our club, I usually end up with a jumble on one side of the table saw and another mess on the jointer bed. It can get to be a real mess.

Talking while turning can be a real challenge. I usually pause in my turning, removing the tool from the wood, before talking.

And in the end, the response from the audience makes all the effort worthwhile.

Re: Reflections from my first demo (long)

#3

Re: Reflections from my first demo (long)

john lucas

>Doug You nailed it. Preparation always takes me longer than I think. I wish I would take the time to build a tool stand like Mark StLeger does. That way every tool is exaclty where it should be, all the time. I try to lay the tool in order but they never stay that way. I have always been mildly annoyed when turners spend a good while searching for a tool. I've done it also and realize it's a problem so I try to lay everything out and where I can find it to keep that to a minimum.

Sound like you did a great job. I haven't tried a hat yet. Maybe with your new tools some skill will rub off and I can try a successful one.

Re: Reflections from my first demo (long)

#4

Re: Reflections from my first demo (long)

robo hippy

>I learned to demo by setting up a lathe in front of the local Woodcraft store on their sale days. I would just turn, and let people ask questions. This is how I found out what people wanted to know.

Do make a list, and check it twice. I once went to a demo and forgot the tool rest for my McNaughton coring system.

Find out what lathe you are turning on, and what adaptations you will have to make.

I just finished filming a DVD. Having a script helped, but of course I would forget parts of it. When you forget something in a demo, someone will always ask that question.

robo hippy

Re: Reflections from my first demo (long)

#5

Why the demo was successful

Gordon Seto

>I am a member in the demo committee of our Club; I appreciate Doug helping me out by agreeing to do his first demo. It was a total success. The response was better than some pro turner demonstration.

To be honest, I didn't have high expectation on this hat demo. It was not that I have doubt about Doug's skill. The general membership in our Club are more mature. I doubt many of them would have a strong back to mount a 55+ pounds of hat blank on their lathes. The younger members who have the physical ability won't be able to turn a hat on their mini lathes or 12" swing lathes. I expect this would be an entertainment demo. When he emphasis that the hat turning skill can be applied to thin wall turning, that is something that we all can use.

This was the fourth hat demo I have seen; and it was the best for a non-hat turner. I don't know what kind of preparation Doug has gone through. He took his first demo very serious. He had spare light bulb for the spare. The only thing he forgot was the leaflets for his Thompson Tools. I believe he has done some practice runs; the timing was right. He didn't waste any time in the setup. He took the time to show us the details of the cuts.

On the other hand, I have seen professional demonstrator that was so confident that he found out the assistants didn't have the setup right, the spare light didn't work when he needed them. Ending up he had to rush through the project. As audience, I couldn't learn much.

There were also a lot of questions asked during and after the demo. That is a good sign to gauge that it was a successful demo.

Doug, if you don't tell you were "forcing" the cut, we didn't know that.

Gordon

Re: Reflections from my first demo (long)

#6

Re: Reflections from my first demo (long)

Bill Grumbine (Kutztown PA)

>Congratulations on a successful demo Doug! The first is the hardest, and they get easier as you go. Just to add a couple of observations based on my own experience, in a demo, I don't worry about making a piece perfect. That is what my show and tell is for. I am there to show a process, not turn a gallery quality piece. The club already thinks I can do that, which is why I am there in front of them all.

Second, like John says, it can get a little irritating when someone can't find a tool, especially when it is me! So, in case there are lapses in the action, I always try to have a story on hand to tell while I am looking. This doesn't happen so much with a single evening short demo, but I just finished two days in MA, and tools were getting scattered. I was in a strange shop, but I can lose them in my own shop, so that was no excuse! This is also a good opportunity to do things like let the people out of their chairs for a break, or to let them come up and see things up close, or ask if there are any questions. These are all good things to do anyway, but they help cover you if you are looking for something. Of course, I have now broadcast one of my big secrets!

Each time you do it, it will get a little easier, and a little smoother - until you decide to do something else. But even then, the experience will carry you through. Be prepared, don't do anything new, and above all, have fun up there, even though they are all looking at you. When you are enjoying yourself, it carries through to your audience.

Bill

Re: Reflections from my first demo (long)

#7

let's add some more to it

Doug Thompson near Cleveland

>It only normal to focus on things that didn�t go so well because this is what needs to be improved upon the next time. Here�s a few things that helped.

Gordon was the contact person from the domo committee and BTW the only reason I said yes to the demo. A good month before he asked what was needed for the demo so the club was prepared to provide what was necessary for the demo... table, outlets etc.

A week before Gordon sent detailed directions to the building (not just a google map) including a satellite view with arrows pointing to each road to travel right to the building the demo was in. This was a huge help.

Get to the demo early so your not in a last minute rush. I was in the area a 1/2 hour before I called to reassure Gordon I didn�t sleep in... LoL

My normal schedule is to go to bed very late and sleep in, to wake up at 6 am when your use to going to be at 4 am is tough. The day before I woke up at 7 am just so I�d be tired enough to go to bed early.

The car was packed the night before and I still forgot a couple unimportant items... Oh well.

I�m the type person that believes if you want something done do it yourself. Let other help, first because they want to and it is a huge relief, second there are other things that need to be taken care of. Your busy with all sorts of questions and they all need an answer... do the best you can.

When you make a mistake keep going , no one will ever say a word about a mistake. Remember many people are thankful your doing the demo and not them.

Bill, wait to see the beautiful setting they hold there club meetings... it�s pretty as a picture.

Re: Reflections from my first demo (long)

#8

Re: Wait a minute here Doug! I made....

Jamie Donaldson

>... a mistake during a demo several years ago, and I'm still hearing about it!!!??? Practice does improve the process, and one of the problems beginners have is timing the demo accurately. What we can do every day at home is quite different when explaining the process in progress, and a good way to practice is to talk your way thru it out loud at home before taking the talking show on the road. I take you to be a methodical and organized guy, and would expect you to be an accomplished demonstrator- good job!

Re: Reflections from my first demo (long)

#9

Re: Wait a minute here Doug! I made....

Bill Grumbine (Kutztown PA)

>Jamie, Jamie, Jamie. When you make a mistake during a demo, you are supposed to say, "I did that on purpose to show you one of the things that can go wrong. Now I'll show you how to fix that!"

Bill

Re: Reflections from my first demo (long)

#10

Re: let's add some more to it

Bill Grumbine (Kutztown PA)

>I'm looking forward to it Doug! I'm going to be out there in November. Maybe I will see you there!

Bill

Re: Reflections from my first demo (long)

#11

Re:Bill- it's impossible to be ......

Jamie Donaldson

>....subtle when you knock a piece completely out of the chuck jaws!!

Re: Reflections from my first demo (long)

#12

Now we all know...

Doug Thompson near Cleveland

>All kidding aside... it proves one thing. We all make mistakes

or

was that a top you were turning.

It's been a good day so far I only made one mistake... just wait til the wife sees what I did to her truck hauling 200 pounds of steel... Oups

Re: Reflections from my first demo (long)

#13

Re: Wait a minute here Doug! I made....

Jerry Whitaker

>A guy named Joe Millsap from Oklahoma did a hat demo for our club about 4 years ago. It was just a small one turned on a Jet Mini. He turned the lathe off, looked at it for a moment and said that it was finished. At the last minute he said, "I think I will take just a little more off here before I part if off. As soon as he touched the wood with the tool, it exploded and most of the pieces were never found. He never looked up, never said a word....just kept on turning. When he turned off the lathe, he said, "You thought I was turning a hat didn't you"? He had made a small tea candle holder from the remains which went into the raffle. This is the same guy who one time grabbed a hatchet from a guys shop wall, went to the grinder and gave it a good sharpening and turned a weed pot with it. He did, however, use a drill bit to drill the hole in it. Quite entertaining.

Re: Reflections from my first demo (long)

#14

Re: Wait a minute here Doug! I made....

Doug Thompson near Cleveland

>That's a good one Jerry... they tend to disappear when you make a mistake.

Re: Reflections from my first demo (long)

#15

Bill Grumbine - Are you sure

Gordon Seto

>you haven't change your mind? Doug has raised the standard. Our members have test driven the Lexus; We are expecting a Bentley or a Rolls Royce to get excited. (Just kidding)

I am the newest kid in the demo committee and our Club meets on the 3rd Saturday in NE Ohio (about 50 miles South of Cleveland). We are always looking for good demonstrators. If any of you who likes the challenge and demonstrate for us, please contact me. We don't pay extremely well, but we will try to make up with respect and good coordination.

Bill is going to do a two day demo / hands-on for us on November 17 and 18. Bill will travel 400 miles West to our place, we may be a stopover for Bill to demonstrate at clubs West of Ohio. I am soliciting clubs so we can pull our resources together to share the traveling cost for outside demonstrators.

Gordon

Re: Reflections from my first demo (long)

#16

Re: Bill Grumbine - Are you sure

Bill Grumbine (Kutztown PA)

>You're getting a Chevy truck with a fat guy in it Gordon. That is the best I can do! ;-)

Bill

Re: Reflections from my first demo (long)

#17

Re: Bill Grumbine - Are you sure

Doug Thompson near Cleveland

>Bill, while your here we can find a really BIG tree and turn a hat to go with that Chevy. Of course you need to try a Thompson Lathe Tool made here in Ohio.

See you in November