Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

VPS-Level Performance. Fully Managed. No Hassle.

Accessories

Posts

Accessories

#1

Accessories

tm

>I just read a current Woodturning Design Magazine that ran an article on the subject. While I always find this type of thing very useful and interesting

it almost always means another trip to a tool store and more money spent.

Here are the listed accessories from the magazine.

1. spring-loaded punch (for marking centres, rubber capped to avoid hand injury)

2. centre finder

3. dead blow mallet

4. compass

5. pizza cutouts (for use as templates when cutting bowl blanks) I'd rather have the pizza

6. CA glue

7. various calipers

8.WD-40 or equivalent

9. water spray bottle (for raising grain, green turning, etc.)

10. morse taper jacobs chuck

My list would include

1. blue masking tape (a multitude of uses)

2. box fan (for dust & heat )

3. long hemostats (internal hollow form sanding & ever drop something under the ways and cannot reach?)

4. task lighting ( I'm still waiting for someone to invent one thats indestructable as well as practical)

5. paper towels

6. japanese flush cut saw (for removing tenons)

8. plunger type lotion dispensers ( i like these for oil finishes )

9. divided office inbox (for storing sandpaper)

10. magnetic tool holding strip

11. magnet reacher ( I used stiff wire and a large speaker magnet see #3)

12. mechanical grabber type reacher ( by now you may correctly surmise that I tend to drop things often)

13. shop & woody vices

14. magnifier ( i hate missing scratches only to find them too late)

15. shop made bowl depth gauge ( Bill Grumbine style)

16. cordless drill (life as i know it would end without this one)

Re: Accessories

#2

Re: Accessories *LINK*

JKJ in East TN

>It's always nice to see someone else's list to get ideas. Some comments:

>1. spring-loaded punch (for marking centres, rubber capped to avoid hand injury)

What I find better for end grain is a small gimlet. (see link for picture) This makes a suitable indentation for the tailstock/headstock centers with a quick twist. Making a hole instead of a mark has a huge advantage for turning thin spindles (i.e., 1/2" or so), especially in hard and brittle wood in that the conical points from the centers will not tend to split the wood even with considerable compression.

>16. cordless drill (life as i know it would end without this one)

As for the drill, I think a close-quarters angle drill is more useful for woodturning than a conventional drill, primarily since it is gripped near the chuck making it easier to handle and control. Also, I have a love-hate relationship with cordless drills. While I have several and use them daily, I dislike keeping up with the batteries and don't use any around the lathe since the corded drill always reaches and never runs down.

>4. task lighting

As for your task lighting wish, I think something I've never seen would be useful: a chest light! Regardless of how many lights I use and their placement, I'm always standing where I shadow the work.

>7. various calipers

I'd add cheap vernier calipers, i.e., the dirt cheap stamped metal type sold in most hardware stores. I round off the corners of these to make it easy to hold them against the work while spindle turning to specific or repeating diameters. I rarely set them by reading the marks (which are hard to see), but close them on a tapered guage or drill bit when the actual dimension is important.

Some others I'd hate to not have within reach:

- Sissors: both good quality to cut small cloth and paper towel squares and cheap/heavier to cut 400+ grit sandpaper squares

- Sandpaper roll dispensor: I keep 1" and 2" rolls on a long dispensor rod just over the lathe.

- Small flashlight

- Strong magnets: to hold hex keys, the gimlet, burning wire, etc.

- Diamond paddle sharpeners, fine and very fine

- Fire extinguisher

- A chuck for every set of jaws (saves a bunch of time)

- Rack of small plastic tilt-front storage bins: great for small cloth and sandpaper squares, velcro-backed sandpaper disks, beeswax, tufts of steel wool, etc.

- Colored Sharpies: for darkening tool edges before sharpening and for marking existing cracks in blanks while processing and before storing (makes them far easier to evaluate months later)

JKJ


gimlet

Re: Accessories

#3

Re: Accessories

tm

>Good list JKJ ... I was fishing for ideas like yours.

Thanks.

tm