Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

A natural, durable finish with minimal coats and fuss popular among woodworkers, flooring professionals, and furniture makers

Opinions on position of lathe?

Posts

Opinions on position of lathe?

#1

Opinions on position of lathe?

Ruth Niles

>I just had a 6'x 3' slider window put in my "tool wall" and now have to reposition my lathe. The sunlight in the picture is coming from double doors on the south wall, the window is in the east wall, all for optimal sunlight in the winter months.

Also I made a custom wire from the lathe plug to the wall outlet and it's 4' long and I just know you're going to say I have to buy new wire rather than splice an extension, right?


img

Re: Opinions on position of lathe?

#2

Steven Antonucci

Why do you need to move the lathe?

steve antonucci

>If I read it right, the window would be behind you where the tools are? You might need to make a tool caddy, but I'd love to have that natural light behind me when I turned.

Line of fire concerns?

Steve

Re: Opinions on position of lathe?

#3

Re: Why do you need to move the lathe?

Ruth Niles

>Not so much line of fire concerns, Steve, as having the light on my work without getting in my own shadow or having it in my eyes rather than on my work. Because of having light coming from 2 sources that are at 90 degrees from each other, it's not that simple. I'm ok with having the tools another place, it's the lathe I need to decide on because once I get a couple of guys to move it, I'm not going to be able to just move it over more.

Re: Opinions on position of lathe?

#4

Re: Opinions on position of lathe?

Russ Fairfield

>I always like to place the lathe so the natural light is coming in the quadrant from over my right shoulder to the end of the lathe bed. Anywhere else and the light is either in my eyes, my shadow, or there is too much glade. The is no rule that says the lathe has to be square with the walls of the room. Once that obstacle is overcome, there are many more ways to arrange a room to take advantage of natural lighting.

Re: Opinions on position of lathe?

#5

Re: Opinions on position of lathe?

Barry Irby

>I have a north facing window in the wall above and behind the lathe. The tailstock end is actually in front of the window, but the headstock is just to the left of it against the wall. Since the sun never comes in a north window directly, I like it. I would not want to turn with the sun in my face. It seems the light is coming in over your right should now. Do you like that? If so, try to arrange for the same effect when you move the lathe.

Can you make an extension cord for the lathe? A heavy duty cord with appropriate plugs on the ends? Probably not as good as extending the actual cord on the lathe or moving a box closer to the lathe, but it should work. At least until you are sure you like the new setup and are through moving the althe for a while.

Re: Opinions on position of lathe?

#6

Re: Opinions on position of lathe?

Mike Nelson

>Hi Ruth, I agree with Russ the lathe doesn't have to be parallel with the wall. As for splicing the wire, no problem, just use the same gage and stagger the connection so you don't have the hot and neutral taped up on top of each other. Use lots of tape. PS that shop of yours sure looks different than the last pics I saw, nice paint job! Mike

Re: Opinions on position of lathe?

#7

wire options

TDaniel

>Ruth, if you are asking how I would lengthen the wire in my shop I would just make a short extension cord, however, I think the code will say that anything longer than 6 ft to a machine should be armored or in conduit. Although adding a short piece of wire to what you already have will work I would avoid that because the connection could pull apart; connections such as this are supposed to be made inside a box with cord grips on each side. Insurance companies just look for something so they don't have to pay a claim and I guess I can't really blame them but it sure ain't like it used to be.

Re: Opinions on position of lathe?

#8

Re: Why do you need to move the lathe?

Doug Thompson near Cleveland

>Just a idea... hold some of your turnings at spindle height and walk around your shop, the best location might not be next to a wall.

Re: Opinions on position of lathe?

#9

Re: Opinions on position of lathe?

Ruth Niles

>Russ, that's exactly what I thought, too, however I have double doors with a window above them on the wall to the right of my "tool wall" and I get the afternoon sun directly through them. I think I'll have to put my lathe on a swivel base to take advantage of the natural light all day! hmmmmm, can I do that?

Re: Opinions on position of lathe?

#10

Re: Opinions on position of lathe? *LINK*

Bob Fawcett

>Put it on wheels so you can experiment.

I like to put larger power tools on a system that allows the wheels to retract or levelers that allow me to raise the tool off the wheels so it is stable. I don't find that locking casters are stable enough most of the time.

I have used these on several tools to make them stable after installing heavy duty casters. I usually extend the cabinet a bit to allow these to reach the floor.

The URL to purchase is:

http://www.rockler.com/product.cfm?page=2053


levelers

Re: Opinions on position of lathe?

#11

Re: Opinions on position of lathe?

Ruth Niles

>Barry, the existing light in the picture is directly behind the lathe, when I'm turning, I'm actually facing the doors which are open all the time.

I suppose I should make a whole new cord for the lathe rather than splicing a longer length to it. I'm not good at adding electric boxes.

Re: Opinions on position of lathe?

#12

good suggestion

Ruth Niles

>Thanks, Mike, the paint made a world of difference and now if I just had a bathroom out there, I wouldn't have to go in the house except to sleep at night. : )

Great suggestion to stagger the splicing, having those wires stripped, spliced and taped (even with a lot of tape) right on top of each other always bothered me. Now why didn't I ever think of something that simple?????

Re: Opinions on position of lathe?

#13

Re: Opinions on position of lathe?

Carole Valentine

>I would just grab one of my turnings, hold it in front of me in the position that it would be if I were working at the lathe, then move around my shop until I found the place that the light reveals the sanding scratches. Then I would put my lathe as far away from that spot as I could because we all know that sunlight is the actual CAUSE of sanding scratches. ;)))

Is that a bag of marshmallows in the foreground? Never tried turning one of those. LOL

Re: Opinions on position of lathe?

#14

Re: wire options

Ruth Niles

>TD, is anything "like it used to be"?????

Re: Opinions on position of lathe?

#15

Re: Opinions on position of lathe?

Ruth Niles

>Nice idea, Bob, but a lot more work than I want to do by myself. Maybe I have to block off one window!?! nah, there's no such thing as too much daylight.

Re: Opinions on position of lathe?

#16

Re: wire options

Bob Fawcett

>Most of the big box stores sell SJ cable by the foot. You can get it in 12/3 or 12/4 depending on your lathe wiring requirements. Its usually $1-2 a foot.

SJ cable is stranded for flexibility and has a heavy "rubber" outer jacket making it suitable for heavy duty power cord, or if you must, an extension cord.

Re: Opinions on position of lathe?

#17

Re: Opinions on position of lathe?

Bob Fawcett

>Put it where you want and hang a mirror over your shoulder ala Russ's direction for a light source.

Re: Opinions on position of lathe?

#18

LOL!!!!

Ruth Niles

>Gee, I never knew sunlight caused scratches. I never had any before I put that window in!

Yes, it's a bag of marshmallows. hmmm, never tried to turn one. I always wanted to turn a beet. Did you ever notice the beautiful grain in a cut raw beet?

Re: Opinions on position of lathe?

#19

Re: Opinions on position of lathe?

john lucas

>Ruth The first movie studio build by Edison was on a revolving railroad track sort of thing. The entire building could be moved so that the natural lighting would be at the proper angle. That's what you need. Or you could do it on a smaller scale so that just the lathe rotates. Kind of like those rotating restaurants. Of course I'd get sea sick if I had that.

Re: Opinions on position of lathe?

#20

Re: Opinions on position of lathe?

john lucas

>That's hilarious Carole. I thought walking around the room carrying a bowl at arms length would be like well witching. It would dip when you find water. Perhaps you could carry a spalted bowl at arms length over the wood pile and it would find properly spalted wood.

Re: Opinions on position of lathe?

#21

Awesome idea, John

Ruth Niles

>I love the idea of a revolving shop or even just the floor. Bet I can't afford it but it would be fun. Yeah, I'd probably get seasick, too! : )

Re: Opinions on position of lathe?

#22

I had one once...

TDaniel

>followed by a hecuva hangover

Re: Opinions on position of lathe?

#23

Re: Awesome idea, John

Russ Fairfield

>I know where there is an old railroad repair shop with a turntable for the locomotives. You could build your shop on that and rotate it wherever you wanted.

Re: Opinions on position of lathe?

#24

How irresponsible!

Molly Winton

>John I can't believe you'd suggest such an idea. I can just see some newbie rigging up a rotating platform, then when turning step back to review his work and fall off. Their luck they'd have their gouge in hand and fall on it necessitating a trip to the ER.

Re: Opinions on position of lathe?

#25

Re: How irresponsible!

john lucas

>Molly I think you should make it flush with the floor so it rotates very smoothly. Of course then you could get crushed between the lathe and some other tool in your shop. And what would happen if you had a voltage surge like TD is having and it took off at high speed. It would be like one of those merry go round things they always have at the park where kids spin until they get sick.