Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Personalized Wooden Watches, Engraved Free

Voltage problems, now it's high

Posts

Voltage problems, now it's high

#1

Voltage problems, now it's high

TDaniel

>OK, yesterday the electric company increased my voltage so that it was 117 at 5pm; that was good. This morning at 8 oclock it is 130/260, that is bad....I think. What is too high? I hesitate to run any machinery until I know more and there is no one to call until Monday.

Re: Voltage problems, now it's high

#2

Re: Voltage problems, now it's high

Bill Howatt

>It is high, but I don't know if the power company would consider it too high. Do you have faith in your meter's calibration?

I wouldn't worry about motors running at that voltage but I would check the max voltage input spec for any VFD inverter drives.

On the practical side, devices are spec'd for their continuous operation but nobody makes a device that is spec'd for 125V that quickly blows up when the voltage is a few volts over.

Bill

Re: Voltage problems, now it's high

#3

Re: Voltage problems, now it's high

TDaniel

>Thanks Bill

I have 2 lathes with inverters but I have not turned them on since knowing of the voltage problems. I am more concerned about my well pump than anything else because it is 350 feet down. The lathes, if connected, would be getting 260 vac to the inverter. It appears that everyone on my line is having the same problem, at least the ones we have checked. I had the power company check my meter and they verified that it is accurate. So far I have not lost anything unless it was a light bulb.

Re: Voltage problems, now it's high

#4

Jesper, Denmark

Re: Voltage problems, now it's high

Jesper, Denmark

>You do not have to worry. Be Happy. That is a small difference and clearly within the normal fluctuations expected. High voltage is much better than low, where all your motors will have to draw more amps to produce the power they are rated for.

Neither VFD's or squirrel cage motors will be harmed by this and universal motors, such as in hand tools, really don't givce a damn.

All of my old US tools are running 130 Volt 50 Hertz from a transformer or 250-260 Volt single phase 50 Herts. After 5 years, nothing has gone bad, but all the squirrel motor tools run at 20% lower speed.

------

One the other hand, when I do buy new tools, they are naturally designed for 220 volt single phase - much nicer than 120 volt, as they are smaller and the power cord gauges are puny compared with the elephant strings used on 115 volt.

Re: Voltage problems, now it's high

#5

Re: Voltage problems, now it's high *LINK*

Bill Howatt

>Terry,

I found this document which was on the Ontario Hydro One (they run the distribution network for most of Ontario) site. It is a general document, produced with input from various Canadian and US utilities. NOTE: It is a 1.66MB PDF so if you have dial-up it will take a bit of time. It is interesting but only if you are an electrical nut!

There is a table on the document's page 16 which will likely be displayed as page 9 in the Adobe PDF reader. It appears to indicate that 127/254V is the upper end of the range and is within the "mariginal operating range" (106/212V to 127/254V) rather than the "normal operating range" (110/220V to 125/250V) but it doesn't say this is a cast-in-stone upper limit. Obviously, you best talk to your power supplier about this.

Bill


Voltage Information 1.66MB PDF

Re: Voltage problems, now it's high

#6

Thanks Jesper!

TDaniel

>

Re: Voltage problems, now it's high

#7

Re: Voltage problems, now it's high

Walt Ahlgrim

>Hi TD

Low voltage is not much of a problem any more as almost all the newer motors and appliances are rated for use down to 208 volts as a lot of new services are going to 208 3 phase and will never get 240 to there motors

If you are concerned about your wells pump you should look at a pump protection unit like http://www.rockinrwellservice.com/pump_protection.htm

Some have high and low voltage coverage. I thing your local well service company will take your call on Saturday, and give you the best advice.

It looks like well pumps are often rated at 230 volts + or - 10% so 207 to 253 should not be a problem

http://www.goulds.com/pdf/IM096R03.pdf

If you get a �CyperPower� Uninterruptible power supply or UPS it will come with a program that will monitor your power up to 24 weeks. $30.00 to $90.00

http://www.cyberpowersystems.com/products/all/ups/browse-by-category/sl-series/CP550SL.html

Walta


img

Re: Voltage problems, now it's high

#8

Thanks Bill, that is a lot of info....

TDaniel

>I am just above the top limit now according to the chart. That seems to be better than being low but still out of the safe envelope. This info really helps. I am logging my voltage in the event that I lose any motors or controllers. Hopefully I won't need to file a claim but at least this does give me some basis for a claim if that becomes necessary. For anyone else who may be monitoring their voltage now the lowest acceptable voltage appears to be 106/212 and the high is 127/254; anything out of this range should be reported to your power company.

Re: Voltage problems, now it's high

#9

Thanks Walt

TDaniel

>If the problem continues I will have to go to this I think. Good info!

TD

Re: Voltage problems, now it's high

#10

Re: Voltage problems, now it's high

JKJ in East TN

>With that line voltage the biggest threat is to your lightbulbs. Motors and computer power supplies and such should not notice.

In case this is now widely known, you can purchase 130 volt light bulbs, not from the usual outlets but from lighting stores. These last MUCH longer at normal voltages but at the expense of a tiny loss of brightness.

For areas that have chronically high voltage, light bulb "savers" are available which drop into the light socket under the bulb base. I belive most of these work by putting a diode in series to remove on half of the ac wave. They really work but the light output is significantly reduced. I've used these in stairwells where changing the bulb took a ladder and hour of time.

JKJ

Re: Voltage problems, now it's high

#11

what about the MOV (130 volt)

TDaniel

>Some of my things (like the well pump) have a voltage limiting device (MOV) (metal oxide varister) which is supposed to block surges such as a distant lightning strike. I know of a couple of things that I have that have this device on them, however, they are unplugged for now. I know there is one on my pump but I can't easily get to it to check it's value. I guess my machinery will remain unplugged until the power company can get things corrected. I know the MOV's on my 120 volt lines are supposed to fuse at 130 volts. Thanks for your input John! It is all helping.

TD

Re: Voltage problems, now it's high

#12

Re: what about the MOV (130 volt)

Gary in Zirconia, NC

>I had voltage of about 123 and was going through a lot of light bulbs back in the 1960's and called the power company and they came out and put in a new transformer. High voltage is better for a motor than low. And for your pump, with all the wire to go to it, the voltage would be lower than it is in your house.

Re: Voltage problems, now it's high

#13

Thanks Gary.

TDaniel

>I guess it is safe for me to run my machines that do not have the MOV's. Thanks again.

TD

Re: Voltage problems, now it's high

#14

Dick Hines

Re: Voltage problems, now it's high

Dick Hines

>You just can't be satisfy you can they. First the mice are running to slow. Now the mice are running to fast. The next thing you will want the mice to run just right and you will still not feed them the right food. Boy some people!

Re: Voltage problems, now it's high

#15

Re: Voltage problems, now it's high

Gil Jones on Lake Seminole GA

>Hi Terry,

Been checking my voltage (shop and home) for the last few days, and it seems to stay about the same any time of day or night, at 122.5/245. Both 120 buses are within a 1/4-volt of the other.

Hope you get it all resolved soon up yonder. Sure would like to be able to afford the VB36...oh well, some day maybe.

Gil

Re: Voltage problems, now it's high

#16

not mice

TDaniel

>I have Charlie and a cat now, the mice were too slow.

Re: Voltage problems, now it's high

#17

The Big Wire

TDaniel

>Too many houses have been built recently near me and the big wire is no longer big enough it seems. I think the power company is going to double the voltage on the big line but first they have to change out all the transformers to dual input type so they can be easily altered to accept double the voltage. I think they have just been hoping that we would not have 95+ days this year. Don't worry about the VB getting hurt because it is unplugged and will stay unplugged until the voltage is right again. Should I keep it waxed for you?

TD