Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Reach the woodworkers who ACTUALLY BUY

Booted from chat room

Posts

Booted from chat room

#1

Booted from chat room

Bill Neddow

>Anyone having trouble getting into the chat room tonight? I have tried five times and every time I enter my name (it does not show). Then a couple of seconds later I get booted right out and my internet software closed. Honest, I did take a bath. :-)))

Re: Booted from chat room

#2

Bill, I have had puter trouble all day...

TDaniel

>I noticed the light on my power strip flickering so I got my volt-meter and checked my power; I am down to 101 volts. I can't stay logged on more than a few minutes before getting a "no connection" note.

Re: Booted from chat room

#3

Re: Booted from chat room

Wally Dickerman in Arizona

>Bill, just got off the chat room...was on for a half hour and had no problems.

Wally

Re: Booted from chat room

#4

Re: Booted from chat room

John Veerkamp

>Bill I had problems to begin with. I got on but all I got was a blank screen. Finally I re booted my computer and logged back on . Don't know if that was the problem, but I was on the chat for about 5minute.

John

Re: Booted from chat room

#5

Re: Booted from chat room

Bill Neddow

>I'll try rebooting next time.

Re: Booted from chat room

#6

Re: Booted from chat room

RonZ

>Did you pay your dues? =o)

Re: Booted from chat room

#7

Dick Hines

Re: Bill, I have had puter trouble all day...

Dick Hines

>Terry you have got to get the mice to run faster in that little wheel.

Re: Booted from chat room

#8

Re: Booted from chat room

Steve Russell

>Hello Bill,

Sorry to hear of your connection problems during last night's chat. Are you using broadband, or dial up? Have you cleaned your computer cache lately? I've had to reset my cable modem a few times when it started dropping the connection. If you're on broadband, that may help you as well.

BTW, I noticed in your picture last night that you have the Oneway outbound tailstock mounting. How hard was this to setup? Did you use their alignment jig? Any problems getting everything lined up? I need to add one of these to my 2436 and was curious if it was an easy installation... Thanks and all the best to you and yours!

Steve Russell

Wednesday Night Turning Chat Moderator

Re: Booted from chat room

#9

Re: Booted from chat room

Bill Neddow

>Steve, sorry about sending in a picture of a winch and then not showing up to talk about it. But it was not for lack of trying. I will empty my cache, etc. Right now the chat room is working like a charm. Don't know what it was.

The Oneway outboard attachment is dead simple to set up. Adding the tailstock assembly is a little more complicated, but Oneway will rent you a kit with all the necessary equipment and instructions. This makes it very simple. Glad I did not try to set it up without the kit, though. The kit is well worth it and the rental is only a few dollars.

Re: Booted from chat room

#10

Re: Booted from chat room

Steve Russell

>Hello Bill,

No problem, I thought you might be having trouble connecting. It has happened to me before... I've had the big outboard attachment for my 2436 for many years, but I need to add the tailstock mounting option. Glad to hear the alignment jig makes it easier. Looks like I'll be calling Oneway tomorrow... :-)

P.S. I really liked your lift setup! I had thought about making something very similar, but I do not have any welding skills so I opted for the overhead winch mounting instead. It works really well and can lift about 700 lbs, per the specs. Since Oneway says the limit for the 2436 spindle is 600 lbs, I should be Ok... :-) Thanks for your help and assistance. I sincerely appreciate your kindness. Take care and all the best to you and yours!

Steve Russell

EWW, WVP, EWWFS

The Woodlands, Texas