Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Good Hope Hardwoods - Walnut Slabs & Specialty Hardwood Lumber

Travelling Vicmarc VL100 (minigloat)

Posts

Travelling Vicmarc VL100 (minigloat)

#1

Travelling Vicmarc VL100 (minigloat)

Allen Neighbors

>Got the Vicmarc mounted on a 2x10, with the motor hanging off the backside. Already changed the motor out. The one shown is a Marathon, and I replaced it with a General Electric/enclosed fan. The Marathon overheated...

I mounted a piece of 'soft-foot' rubber floor mat on the bottom. I turned a little bit with it on the tailgate. Stays put... no clamping necessary.


img

Re: Travelling Vicmarc VL100 (minigloat)

#2

Re: View two

Allen Neighbors

>The hinge pin comes out so I can move it in two parts.


img

Re: Travelling Vicmarc VL100 (minigloat)

#3

Way to go Allen!

Jorge Castaneda

>I mean that in a couple different ways...

Have lots of fun wherever you go.

Jorge

Re: Travelling Vicmarc VL100 (minigloat)

#4

Re: Travelling Vicmarc VL100

georgetroy

>Way to go Allen. When you take off the tailstock and banjo you have a very light unit to haul around. I like your idea everything is tied together. You may or may not need a spring back to your lathe board to reduce balance. Great idea, now you are ready to give demos to other turners. GT

Re: Travelling Vicmarc VL100 (minigloat)

#5

Dick Hines

Re: View two

Dick Hines

>Have lathe,will travel. Cool idea.

Re: Travelling Vicmarc VL100 (minigloat)

#6

Re: But why is the switch plate backwards??

Jamie Donaldson

>

Re: Travelling Vicmarc VL100 (minigloat)

#7

Re: Travelling Vicmarc VL100 (minigloat)

MountainMan

>That setup looks like an old Sears (Record) lathe I used to have....the weight of the motor kept the belt tension just right!!

Re: Travelling Vicmarc VL100 (minigloat)

#8

Re: Way to go Allen!

Allen Neighbors

>Thanks, Jorge. I showed it to a flatworker down at the fire station this afternoon, and one of the other guys asked me if I would show them how I turn at our next BBQ. Might get some more of them interested in turning. :)

Re: Travelling Vicmarc VL100 (minigloat)

#9

Re: View two

Allen Neighbors

>Now if I only knew how to turn.... :)

Re: Travelling Vicmarc VL100 (minigloat)

#10

Re: Travelling Vicmarc VL100

Allen Neighbors

>George, thanks for the comments. Got the ideas for most of it from TD.

What do you mean about the spring back to the lathe board?

You have to know what you're doing to give demos. :) I don't think I've got enough going for me yet to do demos. I just want to be able to turn a little at Craft Shows (that sort of demo might boost some sales) and when we're not showing our wares, I just want to be able to turn when we're on the road. :)

Re: Travelling Vicmarc VL100 (minigloat)

#11

Re: But why is the switch plate backwards??

Allen Neighbors

>Jamie, I used to be a proof reader at the newspaper... they're printed backwards. :) Just kidding.

The switch was one I had used before, and when I mounted it for this use, I turned it around backwards, because when I'm in a hurry, I can flip the switch in the first movement... going... instead of having to go past the switch and pull it back.

Re: Travelling Vicmarc VL100 (minigloat)

#12

Re: Travelling Vicmarc VL100 (minigloat)

Allen Neighbors

>Yep. And I tried it spinning at 950 rpm... grabbed the chuck and stopped the lathe, momentarily... just to see if a catch would make the belt slip... it will. That's good, for me.

I think I need to strengthen the hinge system, to keep the side pull from causing trouble with the little thin belt.

Re: Travelling Vicmarc VL100 (minigloat)

#13

Re: Forgot to publicly thank TD

Allen Neighbors

>This was the last VL100 that TD had on hand. He offered me a good deal on it, I said I'd take it, he shipped it from GA on Saturday, I received it in Texas, today at noon. That's what I call good service.

Thanks, TD!

Re: Travelling Vicmarc VL100 (minigloat)

#14

The lady with the sewing machine

C.W.Stivison

>has nothing on you now. Have lathe will travel.

CW

Re: Travelling Vicmarc VL100 (minigloat)

#15

Re: Travelling Vicmarc VL100 (minigloat)

Carole Valentine

>Cool, Allen. I should take the extensions off and do that with my Jet mini. It's light enough that I could just plop it onto a workmate and start turning.

The Vic looks brand new, but I assume it wasn't since you had to replace the motor.

Re: Travelling Vicmarc VL100 (minigloat)

#16

Re: Travelling Vicmarc VL100 (minigloat)

Allen Neighbors

>Carole, thanks for the idea about the workmate... I hadn't thought of that. They fold up, won't take up much room. I've turned with it on the tailgate of my truck, and it works nice there, but there will be times that I won't be able to have my truck that close. A workmate would be ideal. :)

The little Vicmarc is new. It's the bench model. Comes without the motor, so you can rig it the way you want it, for travel, demos, etc. It's a lot lighter (even now with this 1/2 horse motor) than the VS model, which only has a 1/3 hp motor, and comes on an enclosed cast iron stand that houses the motor and inverter. The VS model costs twice as much as the bench model, also.

If you do shows, you might want to take your little Jet with you sometimes. I don't think you even have to turn on it, just have a work in progress on it and a few tools so you can do a short demo for those who are interested. At least, next week I'm going to find out if it will enhance sales. :)

Re: Travelling Vicmarc VL100 (minigloat)

#17

Re: The lady with the sewing machine

Allen Neighbors

>That's true. And now she's wondering if we're going to have enough room for all of our stock cases, because besides the lathe, I have to take along a box of finishing supplies, a roll of tools, a box of blanks, a grinder... :)

Re: Travelling Vicmarc VL100 (minigloat)

#18

Re: Travelling Vicmarc VL100 (minigloat)

Charles Watson

>Nice set-up, and a very good lathe. Are you using the standard pulley, and was it a problem to find a motor with the right shaft size and length?

Re: Travelling Vicmarc VL100 (minigloat)

#19

Will we next see a gloat

Stuart Johnson

>about the new 3 bedroom motor home with enough room for the odds and ends?

Re: Travelling Vicmarc VL100 (minigloat)

#20

Re: Travelling Vicmarc VL100 (minigloat)

Allen Neighbors

>Thanks... standard pulley... the Vicmarc pulleys fit a 5/8" motor shaft. Both of these motors had that size. :)

Speaking of pulleys... the one on the lathe, and the one for the motor was rough as a cob. Seems like they were covered with fine sand. Don't know if that's to make the belt grab better, or if it's designed to make it wear out quicker. Also, the belt is certainly a little skinny thing. About 7/16" wide X 1/8" thick, a grooved belt, like the new serpentine belts on cars. I'm afraid to leave the weight of the motor, as tension, on it, so I remove the belt from the motor when I quit turnin' on it for the day... I don't want it to break prematurely.

Has anyone had trouble with the small belts breaking?

Re: Travelling Vicmarc VL100 (minigloat)

#21

no problem.....

TDaniel

>I have left the weight of my motor on mine for about 3 years now with no problem. I sometimes use a bungy cord for additional tension but I do not leave the bungy on when not in use. When it comes time to replace the belt I remember someone posting that you could buy a serpentine belt of a useable length and slit it into halves and get two for the price of one.

Re: Travelling Vicmarc VL100 (minigloat)

#22

Re: Serpentine Belt

Allen Neighbors

>TD, I just got back from all the parts stores in this town, and none of them have a serpentine belt that the grooves will fit the pulley. I took the pulley with me, to try to find an extra to have on hand on the trip.

All their belts, the vees were too blunt and wide to fit the pulley's grooves.

Do you know of a source for the 340 JS belts?

Re: Travelling Vicmarc VL100 (minigloat)

#23

Re: Correction: 340 J3

Allen Neighbors

>

Re: Travelling Vicmarc VL100 (minigloat)

#24

belt

TDaniel

>Al, I wouldn't worry about a spare belt for this trip. If the pulleys are lined up that belt should last a long time. Greg Jensen is now handling Vicmarc I think. Email me if you need his email addy.

Re: Travelling Vicmarc VL100 (minigloat)

#25

Re: belt

Allen Neighbors

>Thanks, TD. I have one on the way from the Belt Store, LaFayette, LA. It's being mailed to my address at the Craft show.

I'll be back online in a couple of weeks... sooner, if they have internet connections where I'm going.

See ya. :)