Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Good Hope Hardwoods - Walnut Slabs & Specialty Hardwood Lumber

Bowl Number 4

Posts

Bowl Number 4

#1

Bowl Number 4

Mike Daddis, Fairport, NY

>Took a while but I finally found more time to play on the lathe again. I found a nice piece of ambrosia maple that was only 2.5" thick. So I tried my hand at turning a shallow bowl. Over all I am pleased, but if to take a close look at the picture, you can see an issue I was having. There were two places on the bottom of the inside of the bowl where the grain of the wood was giving me problems. The spots seemed to be feathering up along the outlines of the grain.

No matter what I tried the issue did not get any better. I tried sharpening my bowl gouge. I tried scraping aggressively and scraping with very light cuts. Finally I gave up and thought maybe sanding woud take care of it. No luck there either. What ever I tried seemed to just push the wave of the grain back as well as the feathering.

The issue was not so pronounced when I finished it with a wipe on poly, however it reappeared when I made the mistake of buffing with white diamond compound...Really highlighted the problem.

Any suggestions?

(Sorry about the photography)


img

Re: Bowl Number 4

#2

Re: Bowl Number 4 Sideview 

Mike Daddis, Fairport, NY

>


img

Re: Bowl Number 4

#3

Re: Bowl Number 4 bottom 

Mike Daddis, Fairport, NY

>


img

Re: Bowl Number 4

#4

Reason so long off the lathe....

Mike Daddis, Fairport, NY

>I needed to build a proper display stand for the bowl. My wife calls it the dining room table.


img

Re: Bowl Number 4

#5

Re: Bowl Number 4

dwr

>Mike,

Have you tries sanding in reverse? It can raise flattened fibers and sand them smooth in most cases...

Dave

Re: Bowl Number 4

#6

cabinet scrapers?

JKJ in East TN

>Mike,

I sometimes attack problem grain with lacquer-based sanding sealer. This stiffens up the grain so it can be cut cleanly. Sometimes, oil or wax does the trick.

And when it gets really nasty, I give up on the gouges and use cabinet scrapers - these are used freehand off the tool rest. I've finished pieces with cabinet scrapers that had been driving me crazy otherwise. The eastern red cedar bowl in the photo below is an example - it would have ended up in the wood-burning stove without the cabinet scrapers.

JKJ


img

Re: Bowl Number 4

#7

Wind Shake or crack?

Jake Niedling

>Looking at the top view of the inside their appears to be two vee shaped lines that are typical of a crack in the wood along the growth rings. If that is the case, then you can't get ride of it. Just a thought.

Re: Bowl Number 4

#8

Re:Actually a good time for .........

Jamie Donaldson

>... thin CA glue to the rescue! Apply a thinned coat of lacquer first to fill the wood around the target area, thus reducing the shiny stripes and off color evidence of CA use. When the CA has set, sand and finish in the regular manner- the fix should be almost invisable.

Re: Bowl Number 4

#9

That's a thing of beauty, that is.

Carol in Illinois

>

Re: Bowl Number 4

#10

Re: Bowl Number 4

Allen Neighbors

>I'm like one of the previous posts. I think it may be wind shake.

I got a couple of Bois d'Arc trees one time that had been taken down by a tree remover thing... a heavy piece of machinery that just reaches out and pulls them over. Both of them were ruined by the cracks that machine put in them... the way they cracked all over, looked like just wind shake, but they were in the center of a large wooded area, and weren't as old as some of the Pecans, Oaks, Locust, and Elms that were in there too, so I know the wind didn't do it.

Everything I turned from them had trouble spots. Most of the wood went for firewood last winter.

Re: Bowl Number 4

#11

Re:Actually a good time for .........

C.W.Stivison

>Mike,

I've had luck using ca glue as Jamie suggested.

CW